background image

13

 

 

The Master sections sums the audio from the six Channels and controls the output signal 
level feeding the main sound system.

 

This section features a Master Output Level control, a three

-

Band Isolator EQ and a pair 

of Analogue VU Meters for monitoring the left and right mix buss signal levels.

 

Additional signal  processing can be  applied by making use  of  the Master Insert sockets 
located  on  the  rear  panel.    These  sockets  break  the  mix  signal  path,  enabling  external 
audio processors to be 

inserted

” 

into the signal chain and on to the mixer outputs.

 

Master Level –

 

The Master Output level is adjusted from fully off to +6dBu gain. For best 

signal to noise ratio (SNR) it is recommended operating the mixer with the knob pointer 
at 

“12 

o

-

clock

” 

or above.  If this results in excessive volume then reduce the gain on the 

connected power amplifiers

 

Isolator  –

 

The  asymmetric  Isolator  offers  full  signal  cut  and  +6dB  of  boost  over  three 

frequency bands, High, Mid, Low. Like an EQ the Isolator can be used for audio frequency 
correction,  however,    unlike  an  EQ  the  Isolator  completely  attenuates  the  signal  when 
the  knobs  are  fully  anti

-

clockwise.  With  the  knob  pointers  in  the  centre  position  the 

frequency response is flat.

 

Output  Meters–

 

The  large  analogue  VU  Meters  allow  for  easy  monitoring  of  the  left/

right  main  Mix  Buss  signal  level.  The  signal  level  is  monitored  post

-

Isolator  but  pre

-

Master Level control. The meter response is the VU (Volume Unit) standard and displays 
the  average  signal  level,  unlike  the  channel  LED  meters  which  are  peak  reading.  Both 
meters  feature  soft  ultra  violet  illumination  providing  a  cool  blue/white  glow  for  easy 
monitoring in low light conditions, without being overly bright or distracting.

 

For lowest distortion and best dynamic range, operate the mixer with the meters reading 
between  –

5

VU  and 0VU,  with signal  peaks no  higher  than  +1VU.  If  the  mix  buss  signal 

level goes above +3VU the meter illumination will flash bright red as a warning.

 

Master Section

 

Summary of Contents for Orbit.6





























Reviews: