8
No.
Description
Number
of pieces
1
Wired fuse
1
2
Washer
2
3
O ring
1
4
Piston
1
5
RING
1
6
Sealing washer
1
7
O ring
1
8
Safety ring
1
9
Wired fuse
1
10
Cylinder
1
11
Cabinet
1
12
Oil change input stopper
1
13
Cylinder base
1
14
Steel ball 4 mm diameter
1
15
Spring washer
1
16
Spring
1
17
Safety valve
1
18
Sealing washer
1
19
Safety valve screw
1
20
Steel ball 6 mm diameter
3
21
O ring
1
22
Bypass valve rod
1
23
Washer
1
24
Valve
1
25
Washer
1
26
Pump cylinder
1
27
Y ring
1
28
O ring
1
29
Duster
1
30
Pump piston
1
31
Stud
2
32
Washer
2
33
Torque spring
2
34
Bolt M10
1
35
Lever bracket
1
36
Screw M8×50
1
37
Washer
10
38
Foot pedal
1
39
Safety bolt M10
1
40
Spring washer
1
No.
Description
Number
of pieces
41
Pedal clutch
1
42
Screw M8×55
1
43
Pedal rod
1
44
Stud
1
45
Stud
2
46
Stud
6
47
Spring washer
12
48
Nut
12
49
Stud
6
50
Wired fuse
1
51
Nut M16×1,25
2
52
Rear wheel
2
53
Nut M16×1,5
2
54
Spring washer 18 mm
2
55
Connecting spindle
1
56
Body
2
57
Nut M16×1,5
2
58
Washer
2
59
Friction casing
2
60
Front wheel
2
61
Front wheel spindle
1
62
Saddle bed
1
63
Stud
1
64
Rod
2
65
Arm
1
66
Stud
1
67
Seat
1
68
Stud
1
69
Spring
2
70
Cover
1
71
Handle
2
72
Handle spindle
1
73
Rotational lever button
1
74
Stud
1
75
Connecting rod
1
LIST OF PARTS
5
Safety regulations for hydraulic lift HJ800
•
The lift is designed for lifting (cars, trailers etc.). When lifting, the lifted load must not be occupied by
persons.
•
The lifted load must be properly secured against unwanted movement (with the help of chock etc.).
•
It is forbidden to work below the load, which is found on the lift! Always secure the load with sufficient
support.
•
Make sure the load does not exceed the permitted maximum load of the lift. Danger of damage to the lift
and load.
•
Only use the lift on a solid and flat surface.
•
Pay careful attention to balancing the load.
•
Check the oil status!
•
The hydraulic lift serves for common lifting of loads (cars etc.).
•
The lift is equipped with wheels to facilitate manipulation. The lift should not be used in any case for
manipulation with loads.
•
Before throwing the packaging material out, make sure no part is left inside. If so, take it out and install it.
Use the part listing for check-up and the installation drawing for guidance.
•
Pedal clutch
(41)
has already been mounted to the lift body, to connect the foot pedal
(38)
use nut
(39)
, washer
(40)
, and screw
(42)
. Mount the pedal clutch and foot pedal and tighten.
•
Lever
(72)
must be inserted in lever bracket
(35)
. Before doing it, loosen washer
(34)
and screw
(36)
under the lever opening to facilitate insertion. Once the lever has been inserted, tighten.
Aerating
•
During preparation and lifting, air can enter the hydraulic system and it is not possible to use the full lift
height.
•
Before first use, loosen aerating valve
(73)
by turning it counter-clockwise.
•
Place the load on the lift.
•
Press the lift foot lever several times briefly and then close the aerating valve.
Lifting the load
•
Place the lift into the body place, which are specified by the vehicle manufacturer for lifting.
•
Turn lever button
(73)
clockwise and close the aerating valve by gently tightening it. Only use relative
strength. Do not tighten completely!
•
Place the lift correctly under the lifted object. Make sure the lifted object is supported steadily and as
close as possible to the gravitational centre. This will restrict the lifts chance of slippage.
•
Raise the lift by pumping the foot pedal until the required height is achieved. Once lifted, support the
object with stable supports.
Releasing the load
•
Slowly turn lever button
(73)
counter clockwise. The release speed is given by the rotation of lever button
(73)
.
ASSEMBLY
OPERATION
