Unimac AIRDRLUMCAK06 User Manual Download

Page: 3 / 7

6 PC. Air Drill Kit

Safety

WARNING

: Some dust created by power sanding, sawing, grinding and other construction activities contains

chemicals known to cause cancer, birth defects, or other reproductive harm. Some examples off these
chemicals are lead from lead-based paints crystalline silica form bricks, cement and other masonry products
Arsenic and chromium from chemically treated lumber.

Your risk from these exposures varies, depending now how often you do this type of work. To reduce your
exposure to these chemicals: work in a well-ventilated area, and use approved personal protective equipment,
such as dust masks that are specially designed to filter out microscopic particles.

•

Keep work area clean. An untidy and cluttered work area increases the risk of accidents.

•

Use personal protection equipment. Always use safety glasses or goggles. A facemask should also be worn
when dust is generated. A respirator should be worn when spray painting, even when using outdoors.

•

Wear suitable work clothes. Don't wear loose fitting clothes or jewellery. They can be caught in moving parts
and may cause injury. For outdoor work rubber gloves and nonslip footwear are advised. Wear a protective
hair net to contain long hair.

•

Take precautions with compressed air. Do not disconnect air hoses or tools when the line is under pressure.
Close off air supply and release pressure first. Do not point tools or direct compressed air at people or
animals.

•

Observe work area environment. Do not expose air tools to rain or wet conditions. Do not use air tools in
close proximity to flammable liquids or gases. The work area should be well lit and ventilated.

•

Keep pets, untrained operators and children away. Children should be kept away from the work area. Do not
permit them to handle the tool or tool cable.

•

Secure the work pieces. Use clamps or a vice to hold work. This will free up both hands to operate the tool,
which is safer.

•

Don't overreach when working. Keep a balanced footing at all times. Avoid abnormal stances and awkward
body positioning.

•

Do not overload or force tools. Tools operate better in the specified performance ranges. Forcing the tool
may cause motor damage.

•

Check for damage. Before further use always check the protection guards carefully to ensure proper
operation and performance. Check for alignment of moving parts, binding of moving parts, breakage of parts,
mountings and any other condition that may affect the tools operation. If the tool suffers severe impact, a
crack or damage may occur do not use a tool if a crack develops or if air is escaping.

•

Use the right tool. Only use air tools for their intended purpose. Do not force a small tool or accessory to do
the job of a heavy-duty tool. Do not exceed recommended air pressure.

•

When changing tools or accessories. Always close off air supply and release pressure before attempting to
loosen any connection.

•

Beware of temperature extremes. The expanding air causes the air tools to run very cold. Light gloves are
advisable for operator comfort. Conversely, the cylinder head and air delivery pipe of the compressor tank
will run quite hot, avoid contact with these.

•

Maintain tools with care. For efficient and safe operation tools should be kept clean. Check the connections
and hoses. If damaged they should be replaced.

•

Avoid unintentional triggering. Do not carry tool or connect them with your finger on the trigger.

•

Don't over-use hoses. Do not carry tools by the hose or use the hose to drag the compressor. Protect hoses
from heat, oil and sharp objects. Avoid draping the hose over the compressor cylinder head.

•

When not in use, your air tools should be stored in a dry area, which is not accessible to children.

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC