background image

2    OM-NGB

IMPORTANT - READ FIRST - IMPORTANT

WARNING:  

THE UNIT MUST BE INSTALLED BY PERSONNEL QUALIFIED 

TO WORK WITH GAS, ELECTRICITY AND PLUMBING. 

IMPROPER INSTALLATION CAN CAUSE INJURY TO 

PERSONNEL AND/OR DAMAGE TO THE EQUIPMENT. 

THE UNIT MUST BE INSTALLED IN ACCORDANCE WITH 

APPLICABLE CODES.

NOTICE: 

LEVEL THE UNIT BEFORE USE.  IT MAY BE PITCHED 

SLIGHTLY TO THE REAR.

CAUTION:  

AN ELECTRICAL GROUND IS REQUIRED.

CAUTION:  

DO NOT LOCATE THE BOILER CABINET DIRECTLY OVER A 

FLOOR DRAIN OR FLOOR SINK. HUMIDITY OR WATER FROM 

A DRAIN WILL DAMAGE ELECTRICAL PARTS OF THE UNIT.

WARNING:  

TO AVOID DAMAGE OR INJURY, FOLLOW THE WIRING 

DIAGRAM EXACTLY WHEN CONNECTING A UNIT.

CAUTION:  

DO NOT USE PLASTIC PIPE. DRAIN MUST BE RATED FOR 

STEAM AND BOILING WATER.

WARNING:  

DO NOT CONNECT THE DRAIN DIRECTLY TO A BUILDING 

DRAIN.

WARNING:  

BLOCKING THE DRAIN MAY BE HAZARDOUS.

IMPORTANT:  

IMPROPER DRAIN CONNECTION WILL VOID WARRANTY.

WARNING:  

ALLOW COOKING CHAMBERS TO COOL BEFORE CLEANING.

WARNING:  

CAREFULLY READ THE WARNINGS AND FOLLOW 

THE DIRECTIONS ON THE LABEL OF EACH CLEANING 

AGENT. USE SAFETY GLASSES AND RUBBER GLOVES AS 

RECOMMENDED BY DELIMING AGENT MANUFACTURER.

WARNING:  

DO NOT MIX DE-LIMING AGENTS (ACID) AND DE-GREASERS 

(ALKALI) IN THE STEAM GENERATOR OR ON THE COOKING 

CHAMBER WALLS.

NOTICE:  

DO NOT USE A CLEANING OR DE-LIMING AGENT THAT 

CONTAINS ANY SULFAMIC ACID OR ANY CHLORIDE, 

INCLUDING HYDROCHLORIC ACID (HCL). IF THE CHLORIDE 

CONTENT OF ANY PRODUCT IS UNCLEAR, CONSULT THE 

MANUFACTURER.

NOTICE:  

DO NOT USE A DE-GREASER THAT CONTAINS POTASSIUM 

HYDROXIDE OR SODIUM HYDROXIDE OR THAT IS HIGHLY 

ALKALINE.

WARNING:  

USE OF ANY REPLACEMENT PARTS OTHER THAN THOSE 

SUPPLIED BY THE MANUFACTURER OR THEIR AUTHORIZED 

DISTRIBUTOR VOIDS ALL WARRANTIES AND CAN CAUSE 

BODILY INJURY TO THE OPERATOR AND DAMAGE THE 

EQUIPMENT. SERVICE PERFORMED BY OTHER THAN 

FACTORY-AUTHORIZED PERSONNEL WILL VOID ALL 

WARRANTIES.

WARNING:  

HIGH VOLTAGE EXISTS INSIDE CONTROL COMPARTMENTS. 

DISCONNECT POWER SOURCE BEFORE SERVICING. 

FAILURE TO DO SO CAN RESULT IN SERIOUS INJURY OR 

DEATH.

WARNING:  

DO NOT EXPOSE SKIN TO ESCAPING STEAM. SEVERE 

BURNS CAN RESULT.

CAUTION: 

MAKING ANY ELECTRICAL OR MECHANICAL CHANGE IN 

THE UNIT WITHOUT PRIOR WRITTEN APPROVAL FROM 

ENGINEERING WILL VOID ALL WARRANTIES.

WARNING: 

ALL POTENTIAL USERS OF THE EQUIPMENT SHOULD 

BE TRAINED IN SAFE AND CORRECT OPERATING 

PROCEDURES.

WARNING: 

DO NOT OPERATE THE UNIT UNLESS ALL REMOVABLE 

PANELS (RIGHT, LEFT, FRONT AND REAR) HAVE BEEN 

PROPERLY INSTALLED.

WARRANTY

Congratulations on the purchase of your new Unified Brands equipment. We hope you 
enjoy many years of reliable service in connection with the same. Please review all of 
the important safety and operational information contained in the Operator’s Manual 
for this equipment before it is placed in service. If you have any questions related to 
equipment set up, operations, or service, please call 888-994-7636.
In addition, please review the sales terms and conditions set forth below.

*****IMPORTANT NOTICE*****

WARRANTIES, LIMITATIONS ON WARRANTIES, AND LIMITATION OF REMEDIES

The following Warranties, Limitation on Warranties, and Limitation of Remedies are 
included in the terms of sale for this product. Please read this entire warranty and all 
warranty modifications, disclaimers, and limitations of remedies set forth herein before 
accepting or using this equipment or product. Customer acknowledges and accepts 
the provisions of this notice by Customer’s acceptance and use of the product. If these 
provisions are not acceptable and agreed to by Customer, then please return this 
product in its unused condition to Unified Brands or a Unified Brands authorized dealer.
UNIFIED BRANDS warrants this product against defects in material and workmanship 
under normal use and services for which this product was designed. This warranty 
runs only to the original end user and is in lieu of any other liability for defects. 
THE WARRANTIES EXPRESSED IN THESE TERMS AND CONDITIONS ARE IN PLACE 
OF ANY AND ALL OTHER EXPRESS WARRANTIES (UNLESS SEPARATELY STATED IN 
PRINTED MATERIAL PREPARED BY US DESCRIBING OUR EQUIPMENT) AND EXCLUDE 
ALL IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY OF 
MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE; NOR ARE THERE 
ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, BY OPERATION OF LAW OR 
OTHERWISE. In no event shall UNIFIED BRANDS be liable for damages or delay or 
for any consequential, special or contingent damages arising out of any breach of 
our warranty, whether or not we have knowledge of specific needs or our employees 
or agents have given any specific assurances. Anyone claiming that there has been 
a breach of warranty by UNIFIED BRANDS must give us written notice within THIRTY 
(30) days after discovery of the relevant defect or the right to assert such claim will 
have been waived conclusively and provided further that any such claim must also be 
asserted within the general warranty period for such equipment and/or parts.
UNIFIED BRANDS will not be liable for any expense incurred without our prior written 
authorization for alterations made outside of our factory or for repairs which are 
not performed by UNIFIED BRANDS authorized service departments using UNIFIED 
BRANDS factory parts. Nor shall we be responsible for the performance of equipment 
as to which any repairs, revisions or alterations have been made by others.
THE EXCLUSIVE REMEDY OF THE USER OR BUYER AND THE EXCLUSIVE LIABILITY OF 
UNIFIED BRANDS OR ANY SELLER OF UNIFIED BRANDS PRODUCTS, FOR ANY AND ALL 
CLAIMS, LOSSES, INJURIES, OR DAMAGES (INCLUDING CLAIMS BASED ON BREACH 
OF WARRANTY, CONTRACT, NEGLIGENCE, TORT, STRICT LIABILITY, OR OTHERWISE) 
RESULTING FROM OR ARISING OUT OF THE USE OF HANDLING OF THIS PRODUCT, 
SHALL BE THE RETURN OF THE PURCHASE PRICE OR AN AMOUNT NOT TO EXCEED 
THE ORIGINAL PURCHASE PRICE OF THE PRODUCT OR, AT THE ELECTION OF UNIFIED 
BRANDS OR THE SELLER, THE REPLACEMENT OF THE PRODUCT.

https://unifiedbrands.net/
Groen-Warranty-Information

Summary of Contents for Groen NGB-3E





















Reviews: