background image

Sheet 2

Page 10

FCC PART 15 COMPLIANCE INFORMATION

The antenna used for this radio must be properly installed and maintained and must 

provide a separation distance of at least 13.4 inches (34 cm) from all persons and must 

not be collocated or operated in conjunction with any other antenna or transmitter.  

Never transmit if any person is closer than the specified distance to the antenna. 
Note that Uniden does not specify or supply any antenna with this transceiver. While 

a 0 dBi gain antenna is normal for a typical installation, the above limit applies to any 

antenna with up to 3 dBi gain.
This device complies with Industry Canada license-exempt RSS standard(s). Operation 

is subject to the following two conditions: (1) this device may not cause interference, 

and (2) this device must accept any interference, including interference that may cause 

undesired operation of the device.
Changes or modifications to this product or use of accessories not expressly approved 

by Uniden, or operation of this product in any way other than as provided in the Uniden 

Owner’s Manual could void your authority to operate this product.
A complete Owner’s Manual in French can be downloaded from http://www.uniden.

com/.

TWO-YEAR LIMITED WARRANTY

WARRANTOR: UNIDEN AMERICA CORPORATION (“Uniden”) 
ELEMENTS OF WARRANTY: Uniden warrants, for two years, to the original retail 

owner, this Uniden Product to be free from defects in materials and craftsmanship with 

only the limitations or exclusions set out below. 
WARRANTY DURATION: This warranty to the original user shall terminate and be 

of no further effect 24 months after the date of original retail sale. The warranty is 

invalid if the Product is (A) damaged or not maintained as reasonable or necessary, 

(B) modified, altered, or used as part of any conversion kits, subassemblies, or any 

configurations not sold by Uniden, (C) improperly installed, (D) serviced or repaired by 

someone other than an authorized Uniden service center for a defect or malfunction 

covered by this warranty, (E) used in any conjunction with equipment or parts or as part 

of any system not manufactured by Uniden, or (F) installed or programmed by anyone 

other than as detailed by the owner’s manual for this product. 
STATEMENT OF REMEDY: In the event that the product does not conform to this 

warranty at any time while this warranty is in effect, warrantor will either, at its option, 

repair or replace the defective unit and return it to you without charge for parts, 

service, or any other cost (except shipping and handling) incurred by warrantor or 

its representatives in connection with the performance of this warranty. Warrantor, 

at its option, may replace the unit with a new or refurbished unit. THE LIMITED 

WARRANTY SET FORTH ABOVE IS THE SOLE AND ENTIRE WARRANTY 

PERTAINING TO THE PRODUCT AND IS IN LIEU OF AND EXCLUDES ALL 

OTHER WARRANTIES OF ANY NATURE WHATSOEVER, WHETHER EXPRESS, 

IMPLIED OR ARISING BY OPERATION OF LAW, INCLUDING, BUT NOT LIMITED 

TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A 

PARTICULAR PURPOSE. THIS WARRANTY DOES NOT COVER OR PROVIDE FOR 

THE REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR CONSEQUENTIAL 

DAMAGES. Some states do not allow this exclusion or limitation of incidental or 

Summary of Contents for PRO 510XL













Reviews: