Uniden DECT 3136BT Owner'S Manual Download Page 37

37

User-generated Data

This warranty does not cover any claimed loss of or damage to user-

generated data (including but without limitation phone numbers, addresses 

and images) that may be stored on your Product.

Statement of Remedy 

If the Product is found not to conform to this warranty as stated above, the 

Warrantor, at its discretion, will either repair the defect or replace the Product 

without any charge for parts or service. This warranty does not include any 

reimbursement or payment of any consequential damages claimed to arise 

from a Product’s failure to comply with the warranty.
Our goods come with guarantees that cannot be excluded under the 

Australian Consumer Law. You are entitled to a replacement or refund for 

a major failure and for compensation for any other reasonably foreseeable 

loss or damage. You are also entitled to have the goods repaired or replaced 

if the goods fail to be of acceptable quality and the failure does not amount 

to a major failure.
This warranty is in addition to and sits alongside your rights under either the 

COMPETITION AND CONSUMER ACT 2010 (Australia) or the CONSUMER 

GUARANTEES ACT (New Zealand) as the case may be, none of which can 

be excluded.

 

Procedure for Obtaining Warranty Service

Depending on the country in which the Product was first purchased, if 

you believe that your Product does not conform with this warranty, you 

should deliver the Product, together with satisfactory evidence of your 

original purchase (such as a legible copy of the sales docket) to Uniden 

at the addresses shown below. You should contact Uniden regarding any 

compensation that may be payable for your expenses incurred in making 

a warranty claim. Prior to delivery, we recommend that you make a backup 

copy of any phone numbers, images or other data stored on your Product, in 

case it is lost or damaged during warranty service.

UNIDEN AUSTRALIA PTY LTD 

Service Division 

345 Princes Highway, 

Rockdale, NSW 2216

Phone number: 1300 366 895

Email: [email protected] 

UNIDEN NEW ZEALAND LTD

Service Division

150 Harris Road, East Tamaki

Auckland 2013

Phone number: (09) 273 8377

Email: [email protected]

Summary of Contents for DECT 3136BT







































Reviews: