Uniden DCT6485 Series Owner'S Manual Download Page 14

[ 1 2 ]   G E T T I N G   S T A R T E D

w w w . u n i d e n . c o m

B. Install the rechargeable battery pack into the handset

Charge the handset battery pack for at least 15-20 hours before using your new cordless 
telephone for the first time!

 The handset is powered by a rechargeable battery pack. The 

battery recharges automatically when the handset is placed in the base unit. To maximize 
the charge capacity of your battery pack, DO NOT plug the telephone cord into the base unit 
and wall jack until the battery is fully charged.

1) Press down on the handset battery case cover (use the finger 

indention for a better grip) and slide the cover downward         
to remove.

2) Plug the battery pack connector (red & black wires) into the jack 

inside the battery compartment (the connector notches fit into 
the grooves of the jack only one-way). Match the wire colors to 
the polarity label in the battery compartment, connect the 
battery, and listen for a click to insure connection.

3) Make sure you have a good connection by slightly pulling on the 

battery wires. If the connection is secure, the battery jack will 
remain in place.

4) Place the battery case cover back on the handset by sliding it 

upwards until it clicks into place.

5) Place the handset in the base unit for 15-20 hours without 

interruption. The base unit's LED light (labeled 

charge

illuminates once the handset is placed in the base. The LED light 
will illuminate whether the battery pack is connected or not.

If the base 

charge

 LED light does not illuminate:

• Check to see if the AC adapter is plugged into the base unit and the electrical wall outlet 

properly (use only the supplied AC adapter. Do not use any other AC adapter.)

• Check to see if the handset is sitting correctly in the base and making good contact with 

the base unit's charging contacts.

Use only the Uniden 
(BT-446) rechargeable 
battery pack supplied 
with your cordless 
telephone.

•Replacement battery 

packs are also 
available through the 
Uniden Parts 
Department at (800) 
554-3988, Monday 
thru Friday from 8:00 
a.m. to 5:00 p.m. or 
online at 

www.

uniden.com

note

UP323BH(DCT6485) OM ENG.book  12 ページ  2003年10月24日 金曜日 午前10時56分

Summary of Contents for DCT6485 Series

























































































Reviews: