manualshive.com logo in svg

Uniden BEARCAT 980, Owner'S Manual

Share
Download
Uniden BEARCAT 980 Owner'S Manual Download Page 3

Uniden is a registered trademark of Uniden America Corporation.

Bearcat is a registered trademark of Uniden America Corporation.

Features, specifications, and availability of optional accessories are all 

subject to change without notice.. 

EXIT Menu .................................................................................................. 15

other FeatUres ....................................................................................... 16

S/RF/CAL/SWR Meter  ................................................................................ 16
Calibrate Standing Wave Ratio (SWR)  ..................................................... 16

preventive maintenanCe  ................................................... 16

maintenanCe  ......................................................................... 17

troUBleshooting  ................................................................ 17

serviCing yoUr transCeiver  ............................................. 18

speCiFiCations ........................................................................ 18

tWo-year eXtenDeD Warranty  ........................................ 20

raDio CoDe DeFinitions  ...................................................... 21

Summary of Contents for BEARCAT 980























Reviews:

No comments

Brands by name

Popular brands

Load more brands