background image

-  26  -

                           

  7.  바늘의  상하위치  조정법  /  ADJUSTING  UP-DOWN  POSITION  OF  THE  NEEDLE 

      (1)  바늘이  침판의  구멍  중심에  들어가는지  확인하여  주십시오.

      (2)  땀수  조절  다이얼을  0에  맞춥니다.

      (3)  미싱의  머리부분을  뒤로  눕힙니다.

      (4)  베드  안쪽의  수평이송완  죔나사①②를  풀어  줍니다.

      (5)  바늘이  최하의  위치에  오게  합니다.

      (6)  그림과  같이  압봉과  침봉과의  간격을13.5mm로  하고  수평이송완  죔나사①②를  고정하여  줍니다.

      (7)  이때,  수평이송완(우)과  링크가  그림과  같이  직각으로  연결되었는지  확인합니다.

      (8)  직각으로  되어  있지  않았을  때는  측판커버B를  열고  나사③를  풀어,  요동축크랭크④를  화살표  방향으로

            움직여서  링크와  직각이  되게  조정합니다.

      (9)  각  부를  조정한  후에는  나사①②③를  모두  꽉  죄여줍니다.

      (1)  Confirm  whether  the  needle  goes  through  the  center  of  the  needle  plate  hole.

      (2)  Set  the  stitch  length  adjust  dial  to"0".

      (3)  Lean  the  machine  head  backward.

      (4)  Loosen  the  feed  shaft  crank  set  screws  ①  and  ②.

      (5)  Lower  the  needle    to  its  lowest  position.

      (6)  Allow  13.5mm  gap  between  the  pressure  bar  and  the  pressure  bar.

            Then  finger-tighten  the  feed  shaft  crank  screws①  and  ②.

      (7)  Check  to  see  if  the  right  feed  shaft  crank  is  connected  with  link  at  right  angles  as

            shown  in  the  finger.

      (8)  When  not  connected  at  right  angles,  open  the  side  cover  B,  and  loosen  the  screw③,  and  then

            adjust  the  feed  rock  shaft  crank(right)④  to  have  right  angle  with  the  link.

      (9)  After  the  completion  of  adjustment,  fully  tighten  the  screw  ①,②  and  ③.

 

Summary of Contents for LT2-H650



































Reviews: