•
The lifetime of the batteries is based on the result of the tests by the company and is not an absolute
measurement. It will vary depending on the temperature and humidity of the installed locations as well as
depending on the frequency of usage and the quality of batteries.
•
The functions, design, and composition of the product may change without prior notification for the
purpose of improving its quality.
The precautionary measures are for the safety of the user, for the prevention of property
damage, and for the avoidance of any inconveniences due to an accident. These must be read
and followed properly.
Back ass’y and front ass’y
Pads for the back ass’y and front ass’y
Touch keypad
Deadbolt
Latch Bolt
Data cable
※
Connect the cable according to the
indicated direction for the connection
terminal on the back ass’y.
※
Connect the cable according to the
indicated direction for the connection
terminal on the back ass’y.
※
They are assembled basically for the
right-hand mode. When the left-hand
mode is used, the user needs to
loosen the 2 fixing bolts and reverse
them at 180degrees and insert them
and fasten them again.
Handle
Mortise cable
Ratchet bolt fixing bolts
Emergency power terminal
Battery cover
The handle is a one-touch type product
developed by the company. When it is
installed successfully, the user just needs to
swing it down to open the door safely and
conveniently when moving from the inside
area to the outside area.
Battery insertion area
registration button
Volume switch
Manual knob
Safety plug (Sold separately)
Strike
Handle Shaft
Handle
Shaft Stopper
User manual
Installation manual
Installation manual
Product warranty
Mortise
Battery 4pcs
Assembly bolts
• Do not disassemble or alter the lock.
• Do not install where the distance over
5mm between the door and door frame.
• Please do not expose the password and
change the password in regularly.
• Batteries should not be exposed directly to
heat sources or flames, or submerged in water,
because they may leak or explode, resulting in
severe damage. Please do not use damaged
batteries.
• Do not press using sharp tools or press
numeric button excessively.
• Make sure the door is completely locked when
going out.
• Place the batteries carefully and correctly according
to their polarity (+/-). If the batteries are inserted
in a wrong way, differently from the indicated
direction or polarity, leakage or rupture could occur.
Pay attention to it.
• Please do not mix old with new batteries or use
different types.
Always use new alkaline batteries.
• Do not clean the product with flammable materials
such as alcohol, benzene or thinners.
Such materials may damage the surface or cause
a fire.
• Replace the current batteries with new ones within
1 week after the battery replacement notification
melody sounded off for the first time.
Safety precautions
Product composition
Front ass'y
Mortise
Back ass’y
Locking the door from the outside.
Locking the door from the inside
Registering and changing the password
Warning
Caution
▶
When the auto lock function is set
▶
Opening the door by using the password
▶
When the manual lock function is set
Caution
Caution
Caution
Caution
Attention
Attention
Upon shipment, the function is set to default. When the door is closed, it will be automatically
locked within 3 seconds due to the function of the auto lock sensor.
Touch the keypad. Then, the door will be locked.
Touch the keypad and enter the password and press the [*] button. Then, the door will be opened.
Warning alarm
When an incorrect password or unregistered smart tag is entered 3 times or more, the security alarm
function will be activated, generating an alarm sound of 80dB or higher for 30 seconds and stopping
the system operation for 30 seconds.
Deleting the smart tag (card)
①
Open the battery cover and short press the [Registration] button one time (A short signal sound
“Bibi” will be generated).
②
Press the number [0] button of the front ass’y keypad for 5 seconds.
③
Then, a sound “Biriri” will be generated for notifying that the deletion is completed.
※
When the smart tag (card) that the user currently carries is registered again following loss of the
previous one, the previous one will be deleted while only the currently registered one can be used.
Auto re-lock function
If the user does not enter the premise within 7 seconds after unlocking the door from the outside by
using the password or the key, or if the user does not go out within 7 seconds after unlocking the
door by pushing the door handle down, the auto re-lock function will be activated, causing the door
to be automatically locked.
• When it is needed to check the password, it is required to keep the door open and touch
the keypad to let the deadbolt come out. In this state, when the user enters the registered
(new) password, the deadbolt will be retrieved as long as the door lock is in normal
condition.
• If no password is entered within 7 seconds after the [Registration] button is pressed, the
registration process will be cancelled while an error sound “Biriri~” is generated.
•Upon shipment, the password “1234” is set to default. Once the product is installed,
the password must be replaced with a new one for using the door lock.
•Do not let others know the password. Change it periodically.
•In preparation for an emergency situation in which there is no way to enter the locked
premise due to loss of the password, it is recommended to carry the smart tag
(card) (Required to register it) always, or keep it in a safe area (in a car).
•
Even when a password is changed, the existing smart tags (cards) can be used without
going through an additional change process.
•
When the batteries are replaced, the existing password will not be deleted due to the
function of memory.
•
When a new password is registered, the previous one will be automatically deleted.
•
•
It is possible to register up to 50pcs of smart tag (card) in the door lock.
When users want to purchase additional smart tags (cards), they can purchase them from the
selling shops or the company’s customer support center and register them.
The wait time for registering a smart tag (card) is about 7 seconds. When 7 seconds pass, the registration
sound will not be generated, requiring the user to go through the registration process again (Example: When
there are 4pcs of key, they need to be registered consecutively).
I
•
•
f the user lost any one of the smart tags (cards) that the user currently carries, the user is immediately
required to utilize the function of deleting or neutralizing the smart tag (card) to prepare for possible
security accidents.
Users are wholly responsible for all the damage due to exposure or loss of the password
the smart tag (card). Users need to take extra precautions in keeping them safe.
• Once the [Registration] button is pressed, if the smart tag (card) is brought into contact within
7 seconds, an error sound “Biriri~” will be generated, cancelling the registration process.
When the registration is completed, while the door is opened, the user must check whether
the door lock works normally.
• If an error sound is generated, during the registration process, for notifying that the time
limit is exceeded, it is required to start the registration process from the initial stage.
Right-hand door: Opening the door from the outside by pushing or pulling it with the right hand.
Left-hand door: Opening the door from the outside by pushing or pulling it with the left hand.
※
Upon shipment, the right-hand door mode is set to default, meaning that there is no need to go
through the setting process when installing it for a right-hand door. If the door is a left-hand type,
it is required to change the direction of the ratchet bolt of the mortise. Otherwise, the door will not
be closed.
1. Press the [Registration] button
1. Press the [Registration] button
While the door is opened, open the battery
cover of the back ass’y, and press the [Register]
button one time (A short starting sound
“Bibi~” will be generated).
While the door is opened, open the battery
cover of the back ass’y, and press the [Registration]
button one time (A short starting sound
“Bibi~” will be generated).
Press the [Registration] button after entering
the password.
Press the [Registration] button after registering
all smart keys.
Enter the new password through the keypad
of the front ass’y. 3~20 digits of numbers,
except for the [*] and [#] buttons.
When the password is registered normally,
a melody “Biriri” will be generated, completing
the registration.
When the password is registered normally,
a melody “Biriri” will be generated, completing
the registration.
3. Press the [Registration] button
3. Press the [Registration] button
2. Enter the new password for registration
(3–20 digits).
4. Complete the registration.
4. Complete the registration.
Bring smart tags (cards) into contact at the touch
plate of the front ass’y in order. When each of
them is registered normally, a short signal sound
“Bibi~” will be generated.
2.Register new smart tags (cards).
▶
Opening the door by using the smart tag (card) or Mechanial key cylinder.
Registering (again) the smart tag (card)
※
The Smart tag need to be purchased separately.
Keyhole for the Emergency key
For UN-6500K & UN-6500 SK
model only
Open Close
Close Open
Touch plate UN-6500 S / SK
* The smart tag needed to be
purchased separately.
Panic release function with handle
After 3 seconds
Insert the key into the keyhole
and turn it to open the door.
Bring the registered smart tag into contact
at the touch plate.
UN-6500 Series
User manual
UNICOR HIGHTECH CO., LTD
www.unicor.co.kr
As this is a keyless digital door lock, damage may occur
to parts of the dead lock system if it is not used according
to the manual. Users should be fully aware of the manual
and how to operate this product.
Caution
- This manual may change without notice in case of product improvement.
- This manual may not be edited or changed without the manufacturer’s prior permission
- Product specifications are subject to change without prior notice.
UN-6500N
UN-6500SK
UN-6500K
UN-6500S
