4
CONNECTION
CONFIGURATION
Connection and configuration procedure
of the Unico Dual Plus 1C module (from FWP 50)
on vehicles with steering wheel commands without long key pressing system
and with RESISTIVE LEARNING Radios (as Macrom, Phonocar, Hardstone).
For GMLAN connections, please consult the appropriate technical sheets of the Paser website: http: /
automotive.paser.it/technical_tables.php.
To connect Unico Dual Plus 1C module, first connect the purple wire of the module to the Key A (or SW 1)
of the radio.
Then connect the grey-black wire of the module to the Key GND (or SW GND) of the radio.
WARNING!
For the correct working of the system, you ALWAYS need to configure the PIONEER radio protocol
(radio profile # 4), regardless of the brand of resistive learning radio installed.
X.
Turn on the panel, the Unico Dual Plus 1C led starts blinking GREEN once and then pauses, which
means that the module is ready to receive the radio profile setting.
Press the button 3 times on the steering wheel commands, check that the interface LED flash-
es 4 times GREEN and then pauses.
Confirm by pressing the SEEK + key shortly from the steering wheel commands: the LED will become
FIXED GREEN.
Press the RESET button 5 times on Unico Dual Plus 1C, the interface will start to flash RED and GREEN
(to simulate the long press system on the steering wheel commands).
Enter the radio's resistive learning menu and memorize the steering wheel commands according to the
radio documentation.
Wait at least 5 seconds during the pairing of one button to the other, the maximum number of keys recov-
ered is 6, excluding the phone keys not recovered.
Save the memorization of the keys following the saving mode of the installed radio.
Switch the panel on and off, the Unico Dual Plus 1C led will return to FIXED GREEN (this will deactivate
the long press simulation of the steering wheel controls).
Finally, you can test steering wheel commands working towards the radio.
WARNING!
In case of an already configured module (starting with FIXED GREEN LED), it is necessary to RE-
SET the module by proceeding as follows:
press the RESET button for 10 seconds then release the button.
at this point, the module is reset, the LED will become BLINKING GREEN and it will be pos-
sible to follow the procedure indicated at point X.
1
UNICO DUAL PLUS 1C
Adapter for CAN BUS 1 WIRE (GM LAN)
protocol Steering Wheel Commands
dedicated to aftermarket radios
rev. 1.15
MANUAL OF INSTALLATION AND USE
UNICO DUAL 1C
UNICO DUAL 1C
is an adapter for the OEM steering wheel commands connection.
Its compatibility extends to a range of vehicles having
CAN BUS 1 wire
protocol best known as GMLAN and
to the most famous aftermarket car radios available on market.
This unit recovers not only the SWC but also the services and the sounds of the car.
The display it is not recovered
The function is totally managed by a microprocessor able to self-recognize the steering wheel commands
protocol. The GMLAN protocol setting is managed in SELF-SELECTION.
SET THE DIP SWITCHES ONLY
WITH UNICO DUAL 1C NOT POWERED
DIP SWITCHES
UNICO DUAL 1C
has 4 dip switches. Please do not set them if not necessary.
NOT USED
DIP 1 ON
CAN BUS 1C
DIP 1 OFF
NOT USED
DIP 1 e 2 ON
OPTIONS MANAGING
(SEE PAGE ATTACHED)
DIP 3 ON
UNIT UPGRADING
DIP 4 ON
ATTENTION! YOU ALWAYS MUST TO SET DIP 4
IN POSITION “OFF” AFTER THE SETTING IS DONE
WARRANTY
THIS PRODUCT IS GUARANTEED FOR TWO YEARS AGAINST ANY MANUFACTURING DEFECT.
PURCHASE INVOICE IS REQUIRED AS A VALIDITY OF THE GUARANTEE
The information in this guide are purely for information purposes, therefore, are subject to change without notice. At the time of publication the information
is correct and reliable. However Paser can not be held responsible for any consequences resulting from errors or omissions in this manual. Paser reserves
the right to improve / change the product or manual without obligation to notify users.
ATTENTION!
In case of radio Pioneer,
phone buttons are NOT managed!
