background image

Page 8 

 

Figure 9: 

 

 

C.

 

The following is detailed explanation of the new settings for QCII over P25. 

1.

 

Binding Feature- 

There are three settings; None, Sub-Group Feature and Call Alert Feature.  For 

TGID paging “None” is selected, for QCII over P25 paging “Sub

-

Group Feature” is selected and 

for Call Alert p

aging “Call Alert Feature” is selected.

 

2.

 

Reset Mode- 

If the

 Binding Feature 

is set for

 

“Sub

-Group Feature" there are five selections.  

a.

 

Auto Reset- 

At the end of the page’s 

voice message the G4/5 goes back to Stand-By 

mode awaiting another QCII page.  

b.

 

Selective Timeout Reset- 

This is similar to an 

analog pager’s Selective Call with Revert 

mode.  

In this case, after the pager receives the QCII page’s message it will continue to 

monitor TGIDs programmed in the 

Revert- Talk Group List 

until the

 Timeout Reset Timer 

value expires. The pager will then go back to stand-by mode awaiting a QCII page.

 

c.

 

Selective Manual Reset- 

Same as the above except one must depress the 

pager’s 

Reset 

Key Button to cause the pager to return to the stand-by mode.

 

 

d.

 

Monitor Timeout Reset-

Monitors all TGIDs programmed

 Talk-Group List 

until the

 Timeout 

Reset Timer 

value expires.  If a TGID with QCII IDs is programmed in this list then upon 

detection of a valid QCII ID the pager will monitor all TGIDs affiliated to the Site for the 
duration of the 

Timeout Reset Timer

.  

e.

 

Monitor Manual Reset- 

Same as the above except

 

one must 

depress the pager’s Reset 

Key Button to cause the pager to return to the stand-by mode.

 

 

3.

 

Timeout Reset Timer- 

Works in conjunctions with the Timeout Reset Modes described above. 

4.

 

Delay N Function

- This works similar to the Delay N function in analog paging.  If there is a 

drop-in carrier after Tone B being sent and the beginning of the associated voice message this 
function ensures the voice message get stored. 

5.

 

Delay N Timer

- Works in conjunction with the Delay N Function setting. 

Summary of Contents for G4















Reviews: