UNI-T UTS3000B/A Series User Manual Download Page 59

Page: 59 / 78

Default

Press

[Default]

key to provide a convenient start environment for measurement.

Press

[Default]

>restore to the factory setting,

1. Reset spectrum analyzer to Spectrum Analyzer (SA) mode.

2. Enter frequency menu.

3. Set the default parameter for some environment.

4. Perform processor test but not affect the correction data.

5. Delete the input and output caches and all trace data.

6. The amplitude values of traces 2, 3, 4, 5 and 6 are not displayed.

7. The amplitude correction factor is turned off but remains in the spectrum analyzer's memory.

8. The limit line test is turned off but the list of limit line remains in the spectrum analyzer's memory.

9. The state is directly set to 0.

The default values of key parameters after reset are as follows:

Belongs to the Menu

Parameter Name

Default Value

FREQ

Start Freq

10MHz

FREQ

Stop Freq

8.4GHz(biggest Freq)

FREQ

Freq Offset

0Hz

AMPT

Ref Level

0dBm

AMPT

Attenuation

Auto/10dB

AMPT

Preamplifier

Off

AMPT

Ref Level Offset

0dB

AMPT

Impedance

50Ω

RBW

Auto/3MHz

VBW

Auto/3MHz

Sweep

Sweep Time

Auto/1ms

Sweep

Sweep Mode

Auto/Swept

Sweep

Points

1001

Sweep

Trigger Type

Free Run

Trace

Select Trace

Trace

Trace Type

Clear/Write

Trace

Detector

Normal

Trace

Update

Trace

Display

Meas

Meas Type

Swept SA

Meas/Setup

Avg|Hold Number

100

Meas/Setup

Avg Type

Voltage

Summary of Contents for UTS3000B/A Series















































































Search results

Summary of Contents for UTS3000B/A Series

Reviews:

Related manuals for UTS3000B/A Series

Brands by name

Popular brands

UNI-T UTS3000B/A Series, User Manual

Search results

Summary of Contents for UTS3000B/A Series

Reviews:

Related manuals for UTS3000B/A Series

Brands by name

Popular brands