UNI-T UT70C Page 11 Operating Manual Download

Page: 11 / 48

HOLD

Any rotary
switch
position

Press

HOLD

to enter and exit the

Hold mode in any mode; the
Meter beeps.

Functional Buttons (2)

Conductance
mode

Press

HOLD

to toggle between

conductance and resistance
value. Present resistance value
is kept.
Press

to select capacitance

test.

A , mA

Press

to select DC or AC

current. DC is default.

OFF

position

To disable the Sleep Mode, press

while turning on the Meter.

REL

Any rotary
switch
position

Press

REL

to enter and exit the

and

mode in any measuring

mode; the Meter beeps.

, V

, A

Press

to enter frequency

measurement mode; the
Meter beeps.

Press

again to enter duty

cycle measurement mode;
the Meter beeps.

Press

again to return to

the last measurement mode;
the Meter beeps.

Display
Backlight

Press

once to turn the Display

Backlight on and it shall shut off
automatically in around 60
seconds later.

Model UT70C: OPERATING MANUAL

Summary of Contents for UT70C

















































Search results

Summary of Contents for UT70C

Reviews:

Related manuals for UT70C

Brands by name

Popular brands

UNI-T UT70C, Operating Manual

Search results

Summary of Contents for UT70C

Reviews:

Related manuals for UT70C

Brands by name

Popular brands