background image

d. Preformed winding squirrel-cage induction electric motor

50.8  

63.6

38.1  

50.8

25.4   

25.4

Sync rotating speed

720~1499

1500~2999

3000 

Peak-peak displacement amplitude (

m)

Plastic support

Rigid support

The standard is formulated by American Petroleum Institute.

29

30

Notes: for AC electric motor, use highest sync rotating speed; for DC electric 
motor, use the maximum power rotating speed; and for serial and 
multipurpose electric motor, use working rotating speed.
c. the maximum allowable vibration for large electric motor
  

NEMA MG1-20.52

Peak-peak displacement amplitude

Rotating speed

3000 and higher 

25.4

1500~2999

999

50.8

1000~1499 

63.6

76.2

The above two standard are formulated by National Electrical Manufacturers 
Association (NEMA)

e. ISO/IS2373 the electric quality standard based on vibration speed amplitute

80<H<132

132<H<225

225<H<400

Quality grade

600~3600

1.8

2.8

4.5

N

Normal

 

600~1800

1800~3600

0.71

1.12

1.12

1.8

1.8
2.8

600~1800

1800~3600

0.45

0.71

0.71

1.12

1.12

1.8

R

Good

 

S

Special

 

Rotating speed

Axis height H

mm

maximum speed vibration rms(mm/s)

r/min

r/min

Summary of Contents for UT313



















Reviews: