UNI-T UPO2000CS Series User Manual Download Page 68 | Manualshive

Page: 68 / 94

background image

UPO2000CS series User Manua

67

•

LRR: Time between the last rising edge of source 1 to the last rising edge of source 2

•

LFR: Time between the last falling edge of source 1 to the last rising edge of source 2

•

LFF: Time between the last falling edge of source 1 to the last falling edge of source 2

8.5 User Defined Parameters

Press the MEASURE button to enter the automatic measurement menu. Then press the F1 key to select the source
of the measurement. The user defined parameter selection interface can be chosen by F4.

User Defined Parameter Selection

Adjust the parameters with the multipurpose knob, press the multipurpose knob button to confirm selection. For
every selected parameter, a * symbol will appear in front of the parameter.

F3 can be pressed to turn off user defined parameter selection menu and the parameters will be display at the

bottom of the screen. For convenience and immediate view of these parameters, up to 5 parameters can be defined
at the same time.

Users can also choose to open the measurement statistical function with the F4 key.

«
...
66
67
68
69
70
...
»

Summary of Contents for UPO2000CS Series































































































Reviews:

No comments

Related manuals for UPO2000CS Series

Brand: MacDon Pages: 2

Brand: MacDon Pages: 214

Brand: MacDon Pages: 32

Brand: SAMCHULLY Pages: 48

Brand: HAGS Pages: 5

Brand: HAGER WERKEN Pages: 2

Brand: Raymarine Pages: 124

Brand: Raymarine Pages: 192

Brand: NatureZap Pages: 2

ProFire Lightbridge

Brand: M-Audio Pages: 8

Brand: M-Audio Pages: 36

Brand: Qlight Pages: 4

Brand: York Pages: 26

Brand: Radial Engineering Pages: 16

Brand: R&S Pages: 61

Marathon Multi600

Brand: Saeyang Pages: 21

Brand: S&C Pages: 11

Smart Plus PHT-35LHS

Brand: Vatech Pages: 190

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands