background image

TOP OF THE CHIMNEY. THE 6-INCH CLASS-A PIPE IS USED AS A CONDUIT FOR THE 3-INCH PELLET 

PIPE. THE  3-INCH  PELLET  PIPE  SHOULD TERMINATE 

FLUSH

  WITH THE  6-INCH  CLASS-A  PIPE  OR 

TERMINATE A FEW INCHES 

ABOVE

 THE 6-INCH CLASS-A PIPE. THE 3-INCH PELLET PIPE SHOULD 

NEVER

 TERMINATE BELOW THE 6-INCH CLASS-A PIPE. 

!

14.CAUTION:  NEVER  UTILIZE  MAKE-SHIFT  COMPROMISES  DURING  INSTALLATION.  NEVER  INSTALL 

ANY  WOOD  STOVE  OR  CHIMNEY  SYSTEMS  OUTSIDE  OF  THE  PROVISIONS  OUTLINED  IN  THE 

NFPA-211 SAFETY STANDARDS (OR CANADIAN EQUIVALENT). 

!

CONNECTING TO A PRE-EXISTING MANUFACTURED CHIMNEY  

!

1. See Diagram #10. 

!

2. The Kimberly™ wood stove heater is approved to use any UL-Listed legally rated 3-inch (7.62 cm) double 

wall (18-gauge stainless steel lined) multi-fuel pellet pipe as a connector form the flue outlet on the stove. We 

recommend  BioVent®  Multi-Fuel  Insulated  Pellet  Venting,  available  from  Unforgettable  Fire™  or  your 

authorized Kimberly™ dealer. A minimum of 5 feet (152.40 cm)  is recommended. All joints must be secured 

with at least 3 self-tapping screws per joint. In addition, ALL wall, ceiling, attic, and roof penetrations must 

include approved wall thimble and/or rafter radiation shields using 6-inch (15.24 cm) Type 103 HT (U.S.) or 

ULC S629 (Canada) Class-A as a conduit in any and all pass-through areas, in accordance with UL-Listed 

wood stove installations, and must meet all county and state requirements for such installations. Never utilize 

make-shift compromises during installation. 

!

3.

CANADA: 

No  chimney  connector  shall  pass  through  an  attic  or  roof  space,  closet,  or  similar  concealed 

space,  or  a  floor,  or  ceiling.  Where  passage  through  a  wall,  or  partition  of  combustible  construction  is 

desired, the installation shall conform to CAN/CSA-B365, Installation Code for Solid-Fuel-Burning Appliances 

and Equipment. 

!

4. To remove any pre-existing creosote and ashes, the chimney should be professionally cleaned. 

!

5. Install a heat and ember resistant flood pad. See 

Floor Protection

 requirements and Diagram #6.  

!

6. Wear gloves during installation to protect your hands and to prevent cuts from sharp metal edges. 

!

7. The  pre-existing  Type  103HT  (U.S.)  or  ULC629  (Canada)  Class-A  UL-Listed  factory-built  thimble  and 

chimney pipe should remain in place at the ceiling through the attic and roof. Any Class-A pipe beneath the 

ceiling thimble can be removed. The 3-inch pellet pipe will connect to the Kimberly™ wood stove heater and 

will exit inside and at the top of the Class-A pipe. 

!

8. CAUTION:  WHEN  VENTING  WITH  THIS  APPROVED  CHIMNEY  SYSTEM,  FOLLOW 

ONLY 

THESE 

INSTALLATION INSTRUCTIONS FOR CONNECTING THE KIMBERLY™ WOOD STOVE HEATER.  

!

9. CAUTION: 

NEVER 

FOLLOW  INSTALLATION  INSTRUCTIONS  OR  CLEARANCE  RECOMMENDATIONS 

WHICH MAY BE PROVIDED BY ANY PELLET PIPE MANUFACTURER. 

!

10.CAUTION:  BEFORE  INSTALLATION,  REMOVE ALL  SILICONE  GASKETS  FROM  THE  JOINTS  OF ANY 

PELLET PIPE (IF PRESENT) AND DISPOSE OF THE GASKETS APPROPRIATELY. 

!

11. CAUTION: 

DO NOT

 USE A REDUCER TO JOIN THE 3-INCH PELLET PIPE WITH THE 6-INCH CLASS-A 

PIPE.  NOTE: THE  3-INCH  PELLET  PIPE  WILL  CARRY THE  FLUE  GASES  FROM THE  STOVE TO THE 

TOP OF THE CHIMNEY. THE 6-INCH CLASS-A PIPE IS USED AS A CONDUIT FOR THE 3-INCH PELLET 

PIPE. THE  3-INCH  PELLET  PIPE  SHOULD TERMINATE 

FLUSH

  WITH THE  6-INCH  CLASS-A  PIPE  OR 

TERMINATE A FEW INCHES 

ABOVE

 THE 6-INCH CLASS-A PIPE. THE 3-INCH PELLET PIPE SHOULD 

NEVER

 TERMINATE BELOW THE 6-INCH CLASS-A PIPE. 

!

12.CAUTION:  NEVER  UTILIZE  MAKE-SHIFT  COMPROMISES  DURING  INSTALLATION.  NEVER  INSTALL 

ANY  WOOD  STOVE  OR  CHIMNEY  SYSTEMS  OUTSIDE  OF  THE  PROVISIONS  OUTLINED  IN  THE 

NFPA-211 SAFETY STANDARDS (OR CANADIAN EQUIVALENT). 

!

www.UnforgettableFireLLC.com

9

Kimberly™ Owner’s Manual

 

Summary of Contents for Katydid






























Reviews: