Underwater Lights USA Sea Vision SV14 Manual Download Page 2

Page: 2 / 8

Introduction:

Congratulations on the purchase of your new weld-in light for

ALUMINUM

hulled vessels. Underwater Lights

USA, LLC takes

pride in providing well designed, high quality and thoroughly tested lights that allow you to “enhance your boating experience”.
These lights can be installed in your vessel for aesthetics, to attract fish, for security and safety.

General Operating Information:

The 150W, HID, gas discharge lamp used in this light is not an instant re-strike lamp. This means that it must be allowed to cool
for approximately 10 to 20 minutes after being shut off before being restarted. HID lamps generally require approximately 2
minutes to reach full brightness and should be left on for a minimum of 10 minutes. Failure to do so may cause the lamp to flicker
when it is turned on the next time.
The light can be operated for a brief period of time when the vessel is out of the water, but, it is crucial that the vessel is in the
water to ensure proper lamp cooling, however, the light can be operated while the vessel is underway.
The main body is designed and tested to act as a

cofferdam for added security.

Depending upon water clarity conditions, the light beam can reach up to 30 meters (100 feet).

General Safety Information:

This light must be welded into an ALUMINUM hulled vessel in accordance with common ship building practices.
Never try to install or remove this light while the vessel is in the water.
High temperature silicone electrical cable must be used between the light and the ballast, standard ships cable can be used from
the A/C power source to the ballast.
Upon proper installation, this light will become part of the vessels grounding and cathodic protection system.
Always disconnect and lock-out power before working on light.
The light should be inspected for moisture every six months.
The light electrical cabling and ballast box should be visually inspected for proper operating condition every six months.
Marine growth should be removed from the glass using a soft brush to allow both heat and illumination to exit the light.

Technical Specifications:

Lamp = 150 Watt - Metal halide - 12,000 Lumens - 7500 Kelvin color temperature - Approximately 3,000 hours life
Glass = Borosilicate glass - 12.7mm (0.5”) thick - 58mm (2.3”) diameter net aperture
Light Common Body Dimensions = 110mm (4.33”) diameter x 180mm (7.0”) long
Smallest Front Flange Dimensions = 120mm (4.72”) diameter x 65mm (2.56”) long
Largest Front Flange Dimensions = 140mm (5.51”) diameter x 213mm (8.39”) long
Construction = Bright dip anodized marine aluminum alloy - Black anodized marine aluminum alloy 5086
Power supply = 120VAC 50/60Hz input, 1.33 Amps - Minimum operating temperature -30°C (-22°F)

Power supply = 240VAC 50/60Hz input, 0.59 Amps - Minimum operating temperature -30°C (-22°F)

Troubleshooting:

Please contact our technical support staff in Florida at 1-954-760-4447, Monday to Friday from 8:00 am to 5:00 pm EST.

Warranty:

Underwater Lights

USA, LLC warrants this light to be free from defects in workmanship and materials for a period of two years

from the date of original purchase (except lamps). Further, misuse, abuse, improper installation, neglect, improper shipping,
damage caused by disasters such as fire, flood and lightning, unauthorized repair or modifications will void said warranty. Should
your light prove defective during the warranty period, promptly contact Underwater Lights

USA, LLC for an RMA number and then

return the light freight prepaid with the RMA number clearly marked on the outside of the shipping container.

SV14 Light

120VAC/150W

240VAC/150W

Underwater Lights USA, LLC

Underwater Lights Europe Sarl

3406 S.W. 26

Terrace, C 6/7

16, rue Rouaze

Fort Lauderdale, FL 33312 USA

06400 Cannes, France