background image

 

CLASSFICATION

    Installation Manual

 

MODEL

ENB-X2

 

DOCUMENT NO

BU No. 8

 

Kia Optima In-Dash Navigation DIY Installation Guide 

VERSION

1.4

 

PAGE

     

 

24 

 

                                                                                                                                                                                                                                               

Information & Manual                               

Copyright ©  2013 UNAVI USA, Inc. All rights reserved.

                                       

Date: 1/30/2013

 

 

Connect the external speaker to the female connector labeled “BUILT-IN SPEAKER”. 

This speaker will allow sound output from the UNAVI system when the audio is in 

XM/Radio/CD/MP3/Bluetooth mode. 

Sound output from the system will use the factory speakers under “AUX” mode only. 

 

If you choose to install the external speaker, choose a location closest to the Driver (exposed         

or hidden) and where it can be mounted from causing any obstructions to other components. 

  RECOMMENDED 

LOCATION 

FOR SPEAKER 

Summary of Contents for Kia Optima 2011+





























Reviews: