background image

5

Test specifications for Enclosure Port Immunity to RF wireless communications equipment

Test  

frequency

Band 

a)

Service 

a)

Modulation 

b)

Maximum 

power

Maximum 

power

Immunity 

Test Level

(MHz)

(MHz)

(W)

(W)

(V/m)

385

380 –390

TETRA 400

Pulse modulation 

b)

18 Hz

1,8

0,3

27

450

430 – 470

GMRS 460, FRS 460

FM 

c)

± 5 kHz deviation

1 kHz sine

2

0,3

28

710

704 – 787

LTE Band 13, 17

Pulse modulation 

b)

217 Hz

0,2

0,3

9

745

780

810

800 – 960

GSM 800/900, TETRA 
800, iDEN 820, CDMA 
850, LTE  Band 5

Pulse modulation 

b)

18 Hz

2

0,3

28

870

930

1 720

1 700 –1 990

GSM 1800; CDMA 1900;
GSM 1900; DECT; LTE 
Band 1, 3, 4, 25; UMTS

Pulse modulation 

b)

217 Hz

2

0,3

28

1 845

1 970

2 450

2 400 –2 570

Bluetooth, WLAN, 
802.11 b/g/n, RFID 2450, 

LTE Band 7

Pulse modulation 

b)

217 Hz

2

0,3

28

5 240

5 100 –5 800

WLAN 802.11 a/n

Pulse modulation 

b)

217 Hz

0,2

0,3

9

5 500

5 785

d)   If the frequency stepping skips over an  ISM or  amateur band,  

as  applicable,  an  additional  test  frequency shall be used in the 
ISM or amateur radio band. This applies to each ISM and amateur 
radio band within the specified frequency range.

e)   Testing may be performed at other modulation frequencies 

identified by the RISK MANAGEMENT PROCESS.

f)   ME EQUIPMENT and ME SYSTEMS with a d.c. power input 

intended for use with a.c.-to-d.c. converters shall  be  tested  
using  a  converter  that  meets  the  specifications  of the  
MANUFACTURER  of   the   ME  EQUIPMENT  or ME SYSTEM. 
The IMMUNITY TEST LEVELS are applied to the a.c. power input 
of the converter.

g)   Applicable only to ME EQUIPMENT and ME SYSTEMS connected 

to single-phase a.c. mains.

h)   E.g. 10/12 means 10 periods at 50 Hz or 12 periods at 60 Hz.

i)   ME EQUIPMENT  and  ME SYSTEMS  with  RATED  input 

current greater than 16 A / phase shall be  interrupted once  
for 250/300 cycles at any angle and at all phases at the same 
time (if applicable). ME EQUIPMENT and ME  SYSTEMS  with  
battery  backup  shall  resume  line  power  operation  after  the  
test.  For  ME  EQUIPMENT  and ME SYSTEMS with RATED 
input current not exceeding 16 A, all phases shall be interrupted 
simultaneously.

j)   ME EQUIPMENT and ME SYSTEMS that do  not  have  a  surge 

protection device in  the  primary power circuit may be tested 
only at ± 2 kV line(s) to earth and ± 1 kV line(s) to line(s).

k)  Not applicable to CLASS II ME EQUIPMENT and ME SYSTEMS. 

i) 

Direct coupling shall be used.

m)   r.m.s., before modulation is applied.

n)   The ISM  (industrial,  scientific  and  medical)  bands  between  0,15 MHz  

and  80 MHz  are  6,765 MHz  to 6,795 MHz;  13,553 MHz  to  13,567 
MHz;  26,957 MHz  to  27,283 MHz;  and  40,66 MHz  to  40,70 MHz.  The 
amateur radio bands between 0,15 MHz and  80 MHz are 1,8 MHz to  2,0 
MHz,  3,5 MHz to  4,0 MHz,  5,3 MHz  to  5,4  MHz,  7  MHz  to  7,3 MHz,  
10,1 MHz  to  10,15 MHz,  14 MHz  to  14,2 MHz,  18,07 MHz  to  18,17 
MHz, 21,0 MHz to 21,4 MHz, 24,89 MHz to 24,99 MHz, 28,0 MHz to 29,7 
MHz and 50,0 MHz to 54,0 MHz.

o)  Applicable to ME EQUIPMENT and ME SYSTEMS with RATED input 

current less than or equal to 16 A / phase and ME EQUIPMENT and ME 
SYSTEMS with RATED input current greater than 16 A / phase.

p)   Applicable to ME EQUIPMENT and ME SYSTEMS with RATED input 

current less than or equal to 16 A / phase.

q)  At some phase angles, applying this test  to  ME  EQUIPMENT  with 

transformer mains  power input  might  cause an overcurrent protection 
device to open. This can occur due to magnetic flux saturation of 
the transformer   core after the voltage dip. If this occurs, the ME 
EQUIPMENT  or  ME  SYSTEM  shall provide BASIC SAFETY  during and 
after the test.

r) 

For ME EQUIPMENT and ME SYSTEMS that have multiple voltage 
settings or auto ranging voltage capability, the  test shall be performed at 
the minimum and maximum RATED  input voltage. ME EQUIPMENT  and 
ME SYSTEMS  with a RATED input voltage range of less than 25 % of the 
highest RATED input voltage shall be tested at one RATED input voltage 
within the range. See Table 1 Note c) for examples calculations.

NOTE If necessary to achieve the IMMUNITY TEST LEVEL, the distance 
between the transmitting antenna and the ME EQUIPMENT or ME 
SYSTEM may be reduced to 1 m. The 1 m test distance is permitted by 
IEC 61000-4-3.

a)   For some services, only the uplink frequencies are included.
b)   The carrier shall be modulated using a 50 % duty cycle 

square wave signal.

c)   As an alternative to FM modulation, 50 % pulse modulation 

at 18 Hz may be used because while it does not represent 

actual modulation, it would be worst case.

Summary of Contents for FUSIONONE 3001





















Reviews: