Full product range & more information:
www.lumenalights.com
WIRING / CONNECTION:
IMPORTANT:
1.
If buried or laid on muddy surface, cable should be placed inside conduit or piping to protect from water-logging, damage
and chemicals found in soil. If this method is not used, cable warranty may be void. Cables can also be hooked up on fences
safely, however protective sleeving is still recommended.
2.
It is recommended that the number of fittings on each circuit are kept to a minimum, fittings are positioned as evenly as
possible around a circuit and each run kept as short as possible to prevent voltage drop. For longer cable runs, thicker cable
(1.5mm or 2.5mm) may be required.
3.
Ensure the transformer has plenty of air circulation to avoid overheating.
•
Decide on the positioning of the spike light. See below for mounting installation.
•
Locate the mains electrical supply (pre-installed armoured cable / outdoor socket).
•
Connect the male 2 pin plug of the both spotlights to the splitter by pushing into the female socket.
•
Using a versa extension cable (double male), connect the splitter to the transformer (or splitter for a larger install).
NOTE: A small rubber o-ring must be present in the external groove of the male plug.
•
Secure all VERSA 2 pin plugs in place with the threaded cap.
•
Ensure all connections are tight.
•
Install lamp (see below)
•
Connect the transformer to the mains supply (plug supplied can be
removed).
•
If preferred, cable tie the cables to the back of the pole, one under the
twin adaptor (top of pole) and one just above the ground spike.
•
Once fully installed, turn on the mains power.
MOUNTING:
1.
Tilt the spotlight heads to create plenty of room between the head and twin adaptor.
2.
Remove the socket screw, locknut and washers from the adaptor with the allen key provided.
3.
Attach each head to the top of the adaptor (smooth side) with the removed screws, washers and nuts, facing away from each other
to leave a large gap in the centre (see pics B & C). These can be adjusted later by loosening the socket screws slightly.
TIP:
for ease
of loosening / tightening screws (due to little clearing for the allen key) hold the socket screw securely with the allen key and tighten
the nut with an 8mm spanner.
4.
Remove the socket screw and washer from the pole, place the adaptor on top of the pole using the guide
underneath the adaptor and attach with the socket screw / washer by hand.
5.
Place the allen key inside the socket screw of the pole to hold firmly in position and turn the pole by hand to
tighten fully (see pic D).
6.
Screw the threaded 4 fin ground spike to the bottom of the pole by hand and securely tighten.
7.
Dampen the ground in the area where the fitting is to be installed.
8.
Carefully, push the spike into the ground to the desired depth with the centre of the twin adaptor. Do
NOT
put pressure on the spotlight heads.
9.
Gently compact the earth around the spike to ensure the spike is mounted firmly in the
ground and does not move from side to side.
10.
Adjust the position of the spotlights heads if desired and ensure the locknuts are
securely fastened.
ADJUSTING THE SPOTLIGHT HEAD:
The head can be adjusted and set at various angles via the U Bracket. If this is too secure to adjust, follow the following
steps:
1.
Support the head and slightly loosen the 2 x socket screws found on each side of the U Bracket using the
allen key provided by turning anti-clockwise
–
one turn should be enough to allow the head to move up and
down
(do not fully remove).
2.
Angle the head in the desired position and tighten the loosened screws to secure in place.
3.
If a screw becomes fully removed, return into the outer side of the bracket with a washer on each side as per
image (E).
INSTALLING / CHANGING LAMP:
•
Unscrew the cap of the spotlight by hand (anti-clockwise).
•
Push in the MR16 using the guides to push the pins into the two holes below.
•
Ensure silica gel pack is present (change if damp).
•
Ensure o-ring is present on the male thread of the body and is not twisted.
•
Replace cap and tighten securely by hand (clockwise).
E
B
D
C
