background image

 

8

 

3.5 Oil return mechanism (Option) 
Oil return mechanism is designed to return the trapped oil in oil mist trap to the pump. 3 models of oil 
return mechanism are available according to the operating pressure and conditions. 

Table.2 Oil return mechanism models 

 

Oil return mechanism A 

Oil  returns  into  the  pump  case  through  the  oil  filling  plug.  The  oil  back  to  the  oil  mist  trap  is 
prevented by the check valve. 
  CAUTION: The oil doesn’t returns to the pump when the gas flows in the pump case. Only when 

the pump is operated under no load or at stop. 

 

Oil return mechanism B 

Oil returns into the pump compression process through the gas ballast port. 
  CAUTION:  Oil  return  mechanism  B  shall  cause  to  rise  the  ultimate  pressure.  The  gas  ballast 

cannot  be  performed  unless  the  oil  is  completely  recovered  since  using  the  gas 
ballast port. On the other hand, the ability of oil returns is reduced because the pump 
compression process time is increased for the operation under the high pressure. 

 

Oil return mechanism C 

Oil returns into the inlet port. 
  CAUTION:  At  the  oil  recovery,  Oil  return  mechanism  C  causes  to  rise  the  ultimate  pressure 

because the same as a leak at the inlet port. 

 

Summary of Contents for TM-2





















Reviews: