background image

05 

 
 

 

 

Power Supply 

(10)When attaching the main power cord to the pump, 

please use the power cord which meets the rated 
voltage and current, pursuant to the provision.   
4-Core-cable(Size  of  the  wire  lead:  1.0m

  or  larger, 

300V  or  more,  10A  or  more,

  100

  or  higher,    one 

earth cable included) 
Ensure  that  one  of  the  core  wires  is  used  as  an  earth 
wire. Firmly attach the 6 - 12mm diameter Cable gland 
compatible  cable  fitted  with  the  appropriate  terminals 
(M3 terminal block screws) to a terminal block. 
Tighten the cap of the cable gland by max 2.5N

m. 

Failure  to  follow  these  requirements  may  result  in 
electric shock. 

Wiring and ground construction should be done subject 
to your local law and the safety requirements. 
The wire with insulation having an outer surface that is 
green  with  or  without  yellow  stripes  is  the  grounding 
wire. 

(11) Switch off the main power supply, before disconnecting the power wire from the pump. 

Failure to do so may result in electric shock. 

(12) Touching the power cord with wet hands may result in electric shock. 
(13) Touching electrical wiring etc while inserting the power cord may result in electric shock. 
(14)The electric motor fitted to this pump incorporates a thermal protector; however it is not 

guaranteed to be open when it eventually fails at some time. For safety reasons therefore, it 
is necessary to fit an overload (over current), protection device and an earth leakage 
breaker. 

 
Operation 

(15) This pump is not designed to be explosion-proof. When using the pump, ensure that there 

are no inflammable materials such as solvents, or explosive gases, in the vicinity. Use under 
such conditions may result in injury or fire. 

(16) Inserting fingers or objects into the motor inlet may result in electric shock, injury, or fire. 
(17) Operating the pump with the discharge outlet blocked, or with a device which prevents 

passage of gas to the discharge outlet, may result in rupture of the pump. The internal 
pressure of the pump rises and the pump body may rupture and the motor become 
overloaded. 

 

This pump is not designed to be pressure-resistant. The internal pressure of the pump is 
limited to 0.03 MPa (gauge pressure). 

 

Maintenance and Repair 

(18) The pump should be dismantled or repaired only by a repair technician trained by the 

manufacturer. 

(19) To prevent ingestion of microscopic particles resulting from wear of components, use a dust 

mask and gloves during repair work. 

 

 

 

 

 

!

Warning

 

Summary of Contents for DAT-50DA



























Reviews: