manualshive.com logo in svg

Ulvac C30MVER, Installation, Operation, Maintenance And Troubleshooting Instructions, Page: 82 / 110

Share
Download
Ulvac C30MVER Installation, Operation, Maintenance And Troubleshooting Instructions Download Page 82

 

C30VR Compressor Installation, Operation, Maintenance and Troubleshooting 

 

 

 

 

 

7-4

   

ULVAC CRYOGENICS INCORPORATED

                   

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 

 

Figure 7-5 

Connecting and disconnecting self-sealing coupling with two 

spanners 

 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

                             

 

 
 
9. Install the replacement adsorber.  Remove the two dust caps from the replacement 

adsorber.    Put the adsorber into the compressor so as to place it at the mounting tab 
on the base of the compressor.  Secure the adsorber with the mounting bolt 
temporally.   

 

10. Connect self-sealing coupling to the adsorber with the two spanners.  Tighten the 

coupling referring to Figure 7-5.  Recommended tightening torque is 20N

･

m.  

Connect the coupling quickly to minimize helium leakage. 

 

11. Put the rear panel back on the compressor to align the helium connector of the 

adsorber with the hole of the rear panel and then remove the rear panel again.    Fix 
the adsorber mounting bolt firmly this time.   

TURN with 30mm spanner   

HOLD with 26mm spanner   

(Self-sealing coupling) 

Clockwise: Tightening 

Counter Clockwise: Loosening

 

 
 
 
 

Adsorber 

Flexible hose

 

Figure 7-6 

Remove adsorber mounting bolt 

Figure 7-7 

Slide adsorber outward 

Summary of Contents for C30MVER















































































































Reviews:

No comments