4. Technical data
Engine displacement
37.2 cm
3
Maximum engine capacity
1.2 kW
Bar length
32 cm
Cutter rail length
14” (35 cm)
Chain pitch
(3/8”), 9,525 mm
Chain thickness
(0.05”), 1.27 mm
Idling speed
3100 ± 300
rpm
Maximum speed with cutting equipment
11000 rpm
Chain speed max.
21 m/s
Tank capacity
310 cm
3
Oil tank capacity
210 cm
3
Anti-vibration function
Yes
Chain wheel teeth
6 teeth x 9.525 mm
Chain brake
Yes
Clutch Yes
Automatic chain lubrication
Yes
Low-kickback chain
Yes
Net weight without chain and chain bar
4.5 kg
Net weight (dry)
5 kg
Fuel consumption (specific)
560 g / kWh
LPA sound pressure level (ISO 22868)
100 dB(A)
KPA uncertainty
2.5 dB(A)
LWA sound power level measured
(ISO 22868)
110.9 dB(A)
KWA uncertainty
2.5 dB(A)
LWA sound power level guaranteed
(ISO 2000/14/EC)
112 dB(A)
Ahv vibration (front handle)
(ISO 22867)
max. 5.46 m/s
2
Khv uncertainty
1.5 m/s
2
Ahv vibration (rear handle)
(ISO 22867)
max. 6.21 m/s
2
Khv uncertainty
1.5 m/s
2
Chain type
Kangxin 91S053T
Bar type
Kangxin P014-50SR
Spark plug
L8RTF
Keep the noise emissions and vibrations to a
minimum.
n
Only use appliances which are in perfect working
order.
n
Service and clean the appliance regularly.
n
Adapt your working style to suit the appliance.
n
Do not overload the appliance.
n
Have the appliance serviced whenever
necessary.
n
Switch the appliance off when it is not in use.
n
Wear protective gloves.
5. Before starting the equipment
Danger!
Do not start the engine until the saw is
fully assembled.
Caution:
Wear protective gloves at all times when
handling the chain.
5.1 Fit the chain bar
To ensure that the bar and the chain are supplied
with oil, USE ONLY THE ORIGINAL BAR. The oiling
hole (Fig. 2/Item A) must be kept clear of dirt and any
build-up of residue.
1.
Make sure the Chain brake lever is pulled back
into the DISENGAGED position (Fig. 3A)
2.
Remove the two bar fastening nuts (B). Remove
the cover (Fig. 3B).
3.
Using a screwdriver, run the adjustment screw (D)
COUNTERCLOCKWISE until the TANG (E)
(projecting prong) is to the end of its travel toward
the clutch drum and sprocket (Fig. 3B/3C).
4.
Fit the open end of the chain bar over the die bar
pins (F) (Fig. 3C/3D).
5.2 To install saw chain
1.
Spread chain out in a loop with cutting edges (A)
pointing CLOCKWISE around loop (Fig. 4A).
2.
Slip the chain around the sprocket (B) behind the
clutch (C). Make sure the links fit between the
sprocket teeth (Fig. 4B).
3.
Guide the drive links into the groove (D) and
around the end of the bar (Fig. 4B).
NOTE:
The saw chain may droop slightly on the lower
part of bar. This is normal.
4.
Pull the chain bar forward until the chain is closely
seated. Make sure that all the drive links are in the
groove of the bar.
5.
Fit the clutch cover and fasten it with 2 screws.
Make sure that the pivot (Fig. 3C/Item E) fits into
the chain bar (Fig. 3D/Item G). The chain must
21
GB
Anleitung_BK_100_SPK7__ 14.04.14 13:03 Seite 21
