Ultrak KR4096HN Operation Instructions Manual Download

Page: 9 / 42

Introduction

Reference page

Rear View

AC power socket
This socket connects to the power cord. Insert the cord
firmly.

Input terminals

ALM IN
Use for alarm recording. The alarm sensor is connected
here.
RST IN
Use to stop alarm recording.

• When “ALARM REC DURATION” in “RECORDING

SET UP” menu is set to “MAN1,” the alarm recording
stops when a signal is input to this terminal. The alarm
reset switch is connected here.

• When set to other than “MAN1,” it can be used to

adjust the VCR’s clock.

REC IN
Use to start/stop recording or for series recording.

GND
When a lead connected to other terminals requires a ground,
connect the ground lead here.

Output terminals

ALM OUT
Use to indicate an alarm recording to an external alarm.
MODE OUT
Use to indicate the VCR’s mode of operation.

• When “MODE OUT” in “REAR TERMINAL” menu is

set to “CLOCK ADJ,” the clock of all connected VCRs
can be adjusted. (

page 28)

CLK OUT
Use to control an external camera switcher.
CALL OUT
Use to indicate when a tape reaches its end during
recording or if there has been a problem during recording.

Battery Box
Battery is stored here.

Note

• This VCR contains a special battery. Consult your dealer

to replace it.

REMOTE jack
Remote control is possible by connecting the remote control
unit (R-9100) here. (

page 33)

MIC IN jack
Input jack for a microphone rated at 600

impedance.

AUDIO IN connector
Audio input connector (RCA pin).

AUDIO OUT connector
Audio output connector (RCA pin).

VIDEO IN connector
Input connector for video signal (BNC connector). Connect
cameras here.

VIDEO OUT connector
Output connector for video signal (BNC connector).
Connect a monitor here.

RESET button

page 38

RS-232C terminal (D-SUB 9pin)
Input terminal to connect with a personal computer via RS-
232C cross cable.

For the rating of each connector at the rear panel of VCR,

page 37.

AUDIO

VIDEO

OUT

REMOTE

MIC

RESET

ALM RST

REC GND ALM MODE

CLK

OUT

CALL

BATTERY

OPEN

Note

Ensure the power cord is not plugged into the outlet before connecting to any rear terminals.

Warning:
The included power cord is used for 120 V, 60 Hz.
Never connect to any outlet or power supply having a different voltage or frequency.

Summary of Contents for KR4096HN











































Search results

Summary of Contents for KR4096HN

Reviews:

Related manuals for KR4096HN

Brands by name

Popular brands

Ultrak KR4096HN, Operation Instructions Manual

Search results

Summary of Contents for KR4096HN

Reviews:

Related manuals for KR4096HN

Brands by name

Popular brands