background image

WARNING

:

 

The warnings, cautions, and instructions discussed in this instruction 

manual  cannot  cover  all  possible  conditions  or  situations  that  could  occur.  It  must  be 

understood  by  the  operator  that  common  sense  and  caution  are  factors  that  cannot  be 

built into this product, but must be supplied by the operator. 

 

SAVE THESE INSTRUCTIONS 

IMPORTANT SAFETY CONSIDERATIONS 

 

If mounting this product requires drilling holes, the installer MUST be sure that the 

drilling  process  will  not  damage  vehicle  components  or  other  vital  parts.  Check 

both sides of the mounting surface before drilling begins. Also de-burr any holes 

and remove any metal shards or remnants. Install grommets into all wire passage 

holes. 

 

Do  not  install  this product  or  route  any  wires in  the  deployment  area of  your  air 

bag. Equipment mounted or located in the air bag deployment area will damage or 

reduce the effectiveness of the air bag, or become a projectile that could cause 

serious personal injury or death. 

 

Do not use a pressure washer to clean this product. 

WORKLIGHT

 

USE AND CARE 

 

Do not modify the worklight in any way.

 Unauthorized modification may impair 

the function and/or safety and could affect the life of the product. 

 

Always  check  damaged  or  worn  out  parts  before  using  the  work  light. 

Broken  parts  will  affect  the  worklight  operation.  Replace  or  repair  damaged  or 

worn parts immediately. 

 

Store idle worklight. 

If the worklight is not permanently installed, when the work 

light

 

is not in use, store it in a secure place out of the reach of children. Inspect it 

for good working condition prior to storage and before reuse. 

INSTALL THE WORKLIGHT 

 

Select a mounting location that will give you a maximum beam adjustment range 

and will not cause 

any obstruction for your vehicle’s normal functions. 

 

Drill  a  mounting  hole  for  mounting  bolt  (6)  on  the  mounting  surface.  Insert 

mounting bolt (6) to the middle hole of U bracket (2). Then run hexagon bolt (3) 

from side hole of U bracket, light, then attach Washer (4) and nut (5). Adjust the 

angle of the light body that will give you a maximum beam. 

Summary of Contents for 43194








Reviews: