SETTING #
LED FLASHES
1
2
3
VALET
SETTINGS
SECURE VALET
15 SECONDS
STANDARD VALET
8 SECONDS
OPTION 3
3 HONK
OPTION 1
1 HONK
OPTION 2
2 HONK
PARK LIGHT
OUTPUT
HORN/ AUX OPTIONS
OPTIONS
30 SECOND ON
FOR DISARM
AUX OUTPUT 0.75 SEC
PULSED
POS TRUNK
RELEASE OUTPUT
AUX OUTPUT ACTIVE
WHEN HELD
NORMAL OPERATION
HORN OUTPUT
SETTING
DESCRIPTION
SETTING #
LED FLASHES
1
2
3
4
5
6
7
IGNITION
AUTO-LOCK
IGNITION AUTO-LOCK &
UNLOCK ENABLED
IGNITION AUTO-LOCK
ONLY
OPTION 3
3 HONK
IGNITION AUTO-LOCK
DISABLED
OPTION 1
1 HONK
OPTION 2
2 HONK
HORN SETTINGS
DOOR LOCK
OPTIONS
DOOR LOCK
PULSE TIMES
HORN OUTPUT TIMING
PASSIVE ARMING
PASSIVE
DOOR LOCKS
HORN HONK
DISABLED
DOUBLE UNLOCK /
SINGLE LOCK PULSES
0.25 SECOND
PULSES
LOUD HONK
FULL
PASSIVE ARMING
PASSIVE DOOR LOCKS
DISABLED
HORN HONK
ENABLED
DOUBLE LOCK /
SINGLE UNLOCK PULSES
3 SECOND
PULSES
REGULAR
PASSIVE SAFETY
REARM ONLY
PASSIVE DOOR LOCKS
ENABLED
HORN HONK
ENABLED
SINGLE UNLOCK /
SINGLE LOCK PULSE
S
0.75 SECOND
PULSES
ALL PASSIVE ARMING
DISABLED
SETTING
DESCRIPTION
To Enter Program Mode
1 - Cycle the Ignition Key On/Off On/Off On (Leaving the key ON)
2 - Press and release the Program Switch 1 time.
(HORN will chip to confirm program mode entered)
3 - Press the Lock Button To Enter Menu 1
Press the Unlock Button to Enter Menu 2
4 - Press and Release the Program Switch to advance through the settings.
(
Confirmed by HORN HONK & LED flashes)
5 - Press and hold the Program Switch to change the setting
(
Confirmed by HORN HONK)
6 -
To exit Program Mode, turn ignition key off
(Confirmed by Long HORN HONK)
ENTERING PROGRAM MODE
PROGRAM MODE 1
PROGRAM MODE 2
SYSTEM PROGRAMMING -
Menu 1
PAGE 4
KE-6
INSTALL MANUAL
QUICK VIEW PROGRAM CHART
SHORT HONK
TRANSMITTER PROGRAMMING
ENTERING REMOTE PROGRAM MODE
The system can lean up to 4 different remote’s. Each remote to be used MUST be programmed
together during the same sequence. For security, when a new remote is programmed all
previous remote’s are deleted. Please see remote operation chart for information on using
Second Car / Pad Lock Operations
.
Press and HOLD the valet switch, HORN will HONK ONCE
(If HORN does not HONK repeat step 1)
CONTINUE TO HOLD until HORN HONK 5 times
Press & Release LOCK button on 1st Remote to be
Programmed for Normal Operation
If remote(s) are to be
programmed for "PADLOCK" skip and goto step 6
Press & Release BUTTON 4 on Remote to be Programmed for
2ND CAR OR PAD LOCK
HORN will HONK 1 time to confirm remote has been
programmed (If HORN does not HONK press button again)
HORN will HONK 1 time to confirm remote has been
programmed (If HORN does not HONK press button again)
PROGRAMMING REMOTE’S
Cycle the Ignition Key - ON/OFF ON/OFF ON
(Leaving the key ON)
Turn ignition key OFF to exit remote program mode when all
required remote’s have been programmed.
1 HONK confirms program mode entered followed by
5 HONK confirming transmitter program mode
1 -
2 -
3 -
4 -
6 -
5 -
7 -
8 -
REPEAT STEP 4 IF A SECOND REMOTE IS TO BE PROGRAMMED FOR NORMAL OPERATION
REPEAT STEP 6 IF A SECOND REMOTE IS TO BE PROGRAMMED FOR 2ND CAR / PADLOCK OPERATION
NOTE: ALL REMOTE’S TO BE USED MUST BE PROGRAMMED IN SEQUENCE
WHILE IN REMOTE PROGRAM MODE, RE-ENTERING REMOTE PROGRAM MODE
WILL ERASE ALL PREVIOUS REMOTE’S
SYSTEM PROGRAMMING -
Menu 1
PAGE 5
KE-6
INSTALL MANUAL
TRANSMITTER PROGRAMMING
