Ultra Start 22 SERIES Install Manual Download Page 16

Page: 16 / 24

Setting 1 Ignition Auto Lock

1) Enable

1 Flash/Chirp Doors Lock/Unlock with Ignition key.

2) Ignition Lock

Only

2 Flashes/Chirps Doors Lock when ignition is turned “ON”

only.

*3) Disable 3 Flashes/Chirps Lock/Unlock with remote transmitter ONLY

Press & Release the Program Button 1 Time

(Setting 1) Confirmed with 1 LED flash.

Press & Hold the Program Button

until the appropriate # of park lights/siren chirps, then release

Press & Release the Program Button

to proceed to the next step

Setting 2 Siren Chirp Settings (Auxiliary Connector Pin 5)

1) Lock/Unlock chirps Disable

1 Flash/Chirp Chirps for Panic/Car Finder Only.

2) Lock/Unlock chirps Enable

2 Flashes/Chirps No Chirps for Start ONLY

*3) All Chirps Enable 3 Flashes/Chirps Chirps for all features.

Press & Release the Program Button 2 Times

(Setting 2) Confirmed with 2 LED flashes.

Press & Hold the Program Button

until the appropriate # of park lights/siren chirps, then release.

Press & Release the Program Button

to proceed to the next step.

Setting 3 Door Lock Options

1) Double Unlock Pulse 1 Flash/Chirp .75 Second lock & 2 unlock pulses
2) 3 Second Lock & Unlock 2 Flashes/Chirps 3 Second Lock & Unlock Pulses

*3) .75 Sec Lock & Unlock 3 Flashes/Chirps .75 Second Lock & Unlock Pulses

Press & Release the Program Button 3 Times

(Setting 3) Confirmed with 3 LED flashes.

Press & Hold the Program Button

until the appropriate # of park lights/siren chirps, then release.

Press & Release the Program Button

to proceed to the next step.

Setting 4 Door Unlock & Disarm Pulse Duration

1) Short Pulses 1 Flash/Chirp 125ms pulses on Unlock & Disarm outputs

*2) Normal Pulses 2 Flashes/Chirps 750ms pulses on Lock/Unlock & Disarm outputs

Press & Release the Program Button 4 Times

(Setting 4) Confirmed with 4 LED flashes.

Press & Hold the Program Button

until the appropriate # of park lights/siren chirps, then release.

Press & Release the Program Button

to proceed to the next step.

Setting 5 Active/Passive Locks

No Auto-Lock with Passive Arm

1 Flash/Chirp Doors do not auto-lock with passive arming

*2) Doors Auto-Lock with Passive Arm

2 Flashes/Chirps Doors Lock when passive arming

Press & Release the Program Button 4 Times

(Setting 5) Confirmed with 5 LED flashes.

Press & Hold the Program Button

until the appropriate # of park lights/siren chirps, then release.

Press & Release the Program Button

to proceed to the next step.

*(Default Settings)

INSTALL MANUAL

REMOTE VEHICLE STARTER

PAGE 16

Menu 1- User Settings

Press and

Release the

button for

Menu 1

Press and Release

the Program Button

# of Times for

Setting Chosen

Press and Hold

the Program Button

to Change Option

Ignition 3x

On/Off

On/Off On

Press and

Release the

Program

Button

Summary of Contents for 22 SERIES

























Search results

Summary of Contents for 22 SERIES

Reviews:

Related manuals for 22 SERIES

Brands by name

Popular brands

Ultra Start 22 SERIES, Install Manual

Search results

Summary of Contents for 22 SERIES

Reviews:

Related manuals for 22 SERIES

Brands by name

Popular brands