Ultra Start 22 SERIES User Manual Download

Page: 1 / 24

background image

INSTALL GUIDE

www.ultrastarters.com

Technical Support: 866-698-5872 ext 0

[email protected]

Covers All 22xx and 23xx Series

Advanced Remote Starter/Alarms

The system must be placed into Service Mode before any service work is started on the
vehicle. It is the sole responsibility of the vehicle owner to ensure that this is done. The
manufacturer accepts no liability or responsibility for accidental starting of the vehicle.
CARBON MONOXIDE - Never Start in an Enclosed Building (Garage, Carport etc...)
- The Hood Pin Safety Switch Must Always be Installed!

Warning!!

CARBON MONOXIDE MAY CAUSE SERIOUS INJURY, EVEN DEATH!

It is the sole responsibility of the user to place the system in Service Mode
when parking in an enclosed area

ex: garage

, partially enclosed area

ex: carport,

or when the vehicle is being serviced.

1
2
3
...
»

Summary of Contents for 22 SERIES

























Reviews:

No comments

Related manuals for 22 SERIES

Brand: ABB Pages: 200

Brand: Vector Pages: 12

Brand: Ultra Start Pages: 8

Brand: Ultra Start Pages: 20

Brand: Wallenstein Pages: 11

Brand: A1TECH Pages: 27

Brand: Absaar Pages: 36

Brand: Ultra Start Pages: 8

Brand: idatastart Pages: 24

Brand: Yaber Pages: 52

Brand: walser Pages: 6

Brand: Ultra Start Pages: 8

Brand: Ultra Start Pages: 24

Brand: K9Safety Pages: 9

Brand: Ultra Start Pages: 4

Brand: Ultra Start Pages: 4

Brand: Ultra Start Pages: 16

Brand: Ultra Start Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands