Installation Guide
Installation Guide
PROGRAMMING
PROGRAMMING
8
9
1 Double Pulse Unlock
1 Flash
Single .75sec.Lock pulse and double Unlock Pulse
2 3 Second Lock & Unlock
2 Flashes 3 second pulses for Lock & Unlock
*3 0.75 Second Pulses
3 Flashes 0.75 second pulses for Lock and Unlock
See setting 4 for door unlock and disarm output durations.
1 Ignition Lock & Unlock Enabled
1 Light Flash
Doors Lock / Unlock when the key is turned On/ Off
2 Ignition Lock Only
2 Light Flashes Doors Lock when ignition key is turned ON only
*3 Ignition Auto Lock Disabled
3 Light Flashes Doors do not Lock or Unlock with Ignition key
1 Lock & Unlock chirps
Disabled
1 Flash
Honks for Panic and Car Finder Mode only.
2 Lock & Unlock chirps
Enabled
2 Flashes
Honks for Lock, Unlock, Panic and Car Finder Mode Only.
*3 All chirps enabled
3 Flashes
Honks for Lock, Unlock, Start, Panic and Car Finder Mode.
Press the Program Button 1 time
to select setting 1 (This will be confirmed by 1 LED flash)
Press and hold the Program
Button
until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Button.
Press Program Button momentarily to move to next program step or repeat to change selection.
Press the Program Button 2 times
to select setting 2 (This will be confirmed by 2 LED flashes)
Press and hold the Program
Button
until you receive the appropriate # of park light flashes and/or horn honks
Release the Program Button.
Press Program Button momentarily to move to next program step or repeat to change selection.
Press the Program Button 3 times
to select setting 3 (This will be confirmed by 3 LED flashes)
Press and hold the Program
Button
until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Button.
Press Program Button momentarily to move to next program step or repeat to change selection.
Setting 1- Ignition Auto Lock
Setting 2- Horn Honk Settings
Setting 3- Door Lock Options
PROGRAM MODE 1 - USER SETTINGS
PROGRAM MODE 2 - ADDITIONAL
Press the Program Button 1 time
to select setting 1 (This will be confirmed by 1 LED flash)
Press and hold the Program
Button
until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button .
Press momentarily to move to next program step or repeat to change selection.
Press the Program Button 2 times
to select setting 2 (This will be confirmed by 2 LED flashes)
Press and hold the Program
Button
until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button .
Press momentarily to move to next program step or repeat to change selection.
1 30 Second Parking Lights on Disarm 1 Flash
Park Lights on for 30 seconds on disarm
2 Negative Park Light
2 Flashes
Switches the Park Light and the Trunk Release (3rd Ch) Outputs
3* Normal Parking Lights
3 Flashes
2 Park Light Flashes on disarm
1 5ms Pulsed Output 1 Flash Short (Quiet) Pulses
2 20ms Pulsed Output 2 Flashes Long (Loud) Pulses
*3 10ms
Pulsed Output
3 Flashes Normal (Medium) Pulses
Setting 3 Horn Honk Timing
1 Secure Valet Active
1 Flash Valet only if ignition “ON” and Program Button is held for 15 seconds
2* Normal Valet Active
2 Flashes Valet if ignition “ON” and Program Button is held for 5 seconds
Setting 1 - Secure Valet Mode
Setting 2 - Parking Light Output
Press the Program Button 7 times
to select setting 7 (This will be confirmed by 7 LED flashes)
Press and hold the Program Button
until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button .
Press momentarily to move to next program step or repeat to change selection.
1 Short Pulses 1 Flash 125ms pulses with Unlock and on the disarm output. (.125 second)
2* Normal
2 Flashes
750ms pulses with Lock, Unlock and on disarm output. (.75 second)
Setting 4 - Door Unlock & Disarm Pulse Duration
Note: Programming this option will change the pulse length of this output from 750ms to a
Much shorter pulse of 125ms.
1 Type 1
1 Flash
Pulse after start and with lock
2 Type 2
2 Flashes
Pulse after start only
3* Factory Re-arm
3 Flashes
0.75 second pulse with lock and after shutdown
Press the Program Button 3 times
to select setting 3 (This will be confirmed by 3 LED flashes)
Press and hold the Program
Button
until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Button.
Press Program Button momentarily to move to next program step or repeat to change selection.
Setting 3- Rearm Output-
Yellow Wire on 14-Pin
1 30 Min Run Time
1 Flash
Remote Starter runs for 30min when activated
2 45 Min Run Time
2 Flashes
Remote Starter runs for 45min when activated
3* 15 Min Run Time
3 Flashes
Remote Starter runs for 15 min when activated
1 10 Seconds
1 Flash
10 sec Max time that starter will stay engaged
2 3 Seconds
2 Flashes
3 sec Max time that starter will stay engaged
3* 5 seconds
3 Flashes
5 sec Max time that starter will stay engaged
1 Active Starter Kill
1 Flash
On when locked, Before ignition and 2 seconds after ignition turns off.
2 Passive Starter Kill
2 Flashes Same as setting 1 but will arm 60sec after the ignition turns off.
3* Bypass Module
3 Flashes Output before ignition. Stays on 2 seconds after ignition turns off.
1 Safety ON
1 Flash
Must press the start button twice to remote start the vehicle
2* Safety OFF
2 Flashes Press the start button once to remote start the vehicle.
Press the Program Button 4 times
to select setting 4 (This will be confirmed by 4 LED flashes)
Press and hold the Program
Button
until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Button.
Press Program Button momentarily to move to next program step or repeat to change selection.
Press the Program Button 5 times
to select setting 5 (This will be confirmed by 5 LED flashes)
Press and hold the Program
Button
until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Button.
Press Program Button momentarily to move to next program step or repeat to change selection.
Press the Program Button 7 times
to select setting 7 (This will be confirmed by 7 LED flashes)
Press and hold the Program
Button
until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Button.
Press Program Button momentarily to move to next program step or repeat to change selection.
Setting 4- Run Time
Setting 5-Maximum Crank Time
Setting 6- Starter Kill/ Bypass Module Output-
Orange wire on 14-Pin Con.
Setting 7- Safety Start Mode
PROGRAM MODE 3 - STARTER SETTINGS
1 Type 1
1 Flash
Unlock before start. Lock pulse after start and shutdown
2 Type 2
2 Flashes
Lock pulse only after remote starter shuts off
3*
Normal Operation 3 Flashes
No additional re-lock pulses
Setting 1- Special Door Lock/ Unlock
Press the Program Button 1 time
to select setting 1 (This will be confirmed by 1 LED flash)
Press and hold the Program
Button
until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button .
Press momentarily to move to next program step or repeat to change selection.
Press the Program Button 2 time
to select setting 2 (This will be confirmed by 2 LED flash)
Press and hold the Program
Button
until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button .
Press momentarily to move to next program step or repeat to change selection.
1 Positive Glow/ 30seconds
1 Flash
Waits a maximum 30 seconds before starting.
2 Timed Delay/ 15 Seconds
2 Flashes
Ignition ON for 15 seconds before engaging remote starter
3*Gas/ Negative Glow Plug
3 Flashes
Waits 2 seconds to start if no diesel input is detected
Setting 2- Gas/ Diesel Mode-
Blue Wire on 14-Pin
