background image

 

Issue 2: 17/08/2017  MILLBROOK INDUSTRIES LTD                                                                

 

 

Assembly and fitting  

 

 

Prior to installation, ensure your mattress elevator is suitable for your local 

supply, i.e. 230 Volts 50Hz and UK 3-pin socket (BS1363)   

  
1.

 

Ensure that the bed to which the Ultimate Healthcare mattress elevator is 

fitted has a base of suitable strength and rigidity to support the product.   

 

 

 

2.

 

Having removed the mattress from the bed, place the mattress elevator 

on the headboard end of the bed base with the chrome bars uppermost.  

 

 

3.

 

The end of the base frame should be placed approximately 80mm from 

the end of the bed.   

 

 

4.

 

The two chrome bars are adjustable; these need to be set to suit the 

width of mattress.  To do this, remove the four e-clips on the top and 

bottom bars of the mattress frame and extend to approximately 50mm 

inside the edge of the mattress.  This will ensure full support.  Once done 

so, replace the e-clips.  

 

 

5.

 

Note the Ultimate Healthcare mattress elevator has colour-matched 

retaining straps to identify where they should be fastened.  

 

 

6.

 

Secure the mattress elevator base section to the bed base using:  

• 

The single blue strap along the length and looped under the base.  

• 

The two green straps across the width and looped under the base.  

 

 

 

 

 

 

 

Following step 6, ensure straps are tensioned fully and the mattress elevator is 

retained firmly in place.  See picture below.  

 

 

Summary of Contents for UBEE0001-2













Reviews: