background image

3. INSTALLATION

 

3.1 Installation Instructions

Attention! The appliance must be installed on the solid surfaces like concrete, wood or metal etc.

Never install on flammable surfaces! (plastics, nylon vinyl etc.)
See pages I-II to come up with the most appropriate installation method for your UFO.

 

UFO Black Line can be used horizantally or vertically, but for a higher heating efficiency we recommend horizantal usage.

 

1- Considering the horizantal and vertical usage of the heater, drill four 8 mm diameter holes on the wall to the place where

 

the unit will be installed, with the distances shown in Fig 5-a and Fig. 5-b (P.I)

NOTE: In case of vertical installation, be sure that LED screen on your Black Line heater is downwards. Otherwise it will give

 

an error signal 'Er' and will not work.

 

2- Insert the 8 mm diameter wall plugs,supplied with the unit, into the holes.
3- Mount two of the L shaped legs on the wall using the 5x40 screws supplied with the unit. (Fig. 5-a, 5-b) (P. 

I)

 

4- Mount the other L legs on the unit using the six M5 screws and the small wrench as shown in

 

(Figure-6) (P. 

I) 

(corresponding nuts are already built in on the body of the unit)

 

5- Mount and fix the L shape legs on the wall and on the unit respectively,using the M8x13 bolts and nuts and the washers as shown in

 

(Figure-7) (P. 

I) 

and tighten by using the wrench supplied.

 

6- Depending on the area to be heated the angle of the unit can be adjusted between 0-45 degrees by the help of M8 bakelite head bolt

 

and nut fixture. (Figure-11) (P. 

II)

 

7- The heater can be mounted on the ceiling. See Fig.8-c (P. 

I)

 

Warning! In case of an installation on the ceiling the heater may discolour the surface depending on the surface material.

 

8- Before operating the unit joints should be checked once again.

See Fig. 5-6-7-8 (P. 

I)

 

3.2 Installation Instructions Po Distance

 

Please see Fig. 8-a, 8-b, 8-c and Table 1 (P.I) for minimum safety distances in case of horizantal and vertical installations.

 

For minimum distances from coverage area and other objects please see Fig. 9 (P.I)

3.3 Installation Instructions with Right and Wrong Positions

DIRECT YOUR HEATER TOWARDS THE MOST APPROPRIATE ANGLE

Do not let the light out through window, glasses etc. as the heater primarily heats the locations onto which its light falls.

 

See Fig. 10 (P. 

II)

 

WARNING: UFO Black Line is equipped with electronic sensors against the risk of tipping over in case of faulty

 

installation. If the heater tips over more than 45º angle in horizantal and vertical directions, it will turn off the power

 

by giving an error signal. In this case, unplug the power cable and then plug it again in order to operate your device.

 

Never carry or direct your heater while it is operating. Before carrying and directing your heater, be sure that it is

 

unplugged and cool enough to touch.

 

Please note that in case of vertical installation, LED screen should be downwards. Otherwise it will give an error

 

signal and will not operate. In this case unplug your heater and repeat the installation regarding the position of LED

 

screen.

 

4. Application Fields

 

Application fields of Black Line models. See Table 2 (P. 

III)

5. Technical Information – Heating Area

 

ENGLISH

 

See Table 3 (P. IV)

 

3

 

Summary of Contents for Black Line









Reviews: