14
grille; also check that the front of the fan is free of volatile materials (dust, etc.).
• Place the appliance away from all heat sources (e.g. naked flames, gas stoves, etc.).
• The supporting surface must be stable and flat and even (so that the appliance does not tip over).
• Place the fan away from fabrics (curtains, etc.) or volatile materials that may obstruct the ventilation
grille; also check that the front of the fan is free of volatile materials (dust, etc.).
• Place the appliance away from all heat sources (e.g. naked flames, gas stoves, etc.).
• The supporting surface must be stable and flat and even (so that the appliance does not tip over).
ASSEMBLY
Warning: the fan may only be used if it is fully and correctly assembled, i.e. with the base and pro-
tection grille.
Warning: always disconnect the appliance from the mains supply before assembling.
If in doubt, have a qualified, professional technicin check the appliance or assemble it. To assemble the
fan, use the following figures in the diagram as a reference.
1.Install rear grille (fig.1).
Align the rear grille to the fan assembly.
2. Secure the rear grille nut (fig.2).
3.Insert fan blade (fig.3).
(1)Slide the fan blade into the blade slot until it is fully inserted into the shaft pin.
(2)Screw on the blade knob tightly in an ati-clockwise direction.
4.Install front grille (fig.4).
Mount the front grille(logo in upright position) with the rear grille with the top U clip.
Fasten the 4 clip around the grille.
Tighten the ring lock with a screw driver (fig.5).
5. Pass the power cord through the base plate (fig.6).
6 .Insert the motor assembly into the base plate (fig.7).
7. Twist clockwise to lock (fig.8).
8. Insert the power cable into the base plate catch at the rear of the base plate (fig.9).
USE
Before each use, check that the appliance is in good condition and that the power cord is not dam-
aged: If the power cord is damaged, request that it be changed by the manufacturer’s technical sup-
port service or a person with a similar qualification, in order to avoid any danger.
Plug the appliance into the mains socket.
Ventilation: select the desired speed using the corresponding buttons (Fig.10):
0 – The fan is switched off 1 – Low speed 2 - Middle speed 3 - High speed
Horizontal oscillation(right-left): press the knob located on the body of the motor downwards. To stop
Summary of Contents for TF0300
