background image

DRS220 User’s Guide  

 

 

Unpacking the DRS220 

1.  Remove the DRS220 from the carry case. 

2.  Remove the control box from the storage dock in right side of the weighing 

platform by pulling the control box firmly from the dock. 

3.  Unwrap the coiled cord from around the weighing platform. When using the 

DRS220, ensure the coiled cord does not touch the top of the weighing platform, 
or inaccuracies may result. 

4.  If desired, extend the easel at the top back of the control box by pulling it out.  

The easel may be used straight for hanging, or folded at an angle for resting on 
a level surface. 

Repacking the DRS220 

1.  If extended, restore the easel to the retracted position. 

2.  Wrap the coiled cord counter-clockwise around the weighing platform. 

3.  Push the control box firmly into the storage dock of the weighing platform until it 

snaps in place. 

4.  Replace the DRS220 into the carry case. 

Battery Installation & Replacement 

1.  Remove the battery cover from the rear of the control box by compressing tab at 

the base of the battery cover. 

2.  If necessary, remove old set of batteries. 

3.  Insert 4 ‘AAA’. Replace battery cover by aligning tabs and snapping back into 

place. 

IMPORTANT: TO PREVENT DAMAGE TO THE DRS220, CAREFULLY 
OBSERVE BATTERY POLARITY AS MARKED INSIDE THE BATTERY 
COMPARTMENT. DO NOT LEAVE DEAD BATTERIES INSIDE THE CONTROL 
BOX. REMOVE BATTERIES IF THE DRS220 IS NOT TO BE USED FOR AN 
EXTENDED PERIOD OF TIME. 

 

DRS220 User’s Guide 

Resolution 

The resolution (minimum incremental weight) than can be displayed by the DRS220 
can be adjusted to make the display easier to read. Unstable loads or high winds 
can cause the display to fluctuate erratically. By reducing the display resolution, 
external influences can be minimized. As shipped, the DRS220 is set to 

MEDIUM

 

resolution, suitable for most purposes.  The resolution can be changed to 

LOW

MEDIUM

 or 

HIGH

 by repeated pressing 

 on the keypad. The table 1 illustrates 

the displayed resolution for each units mode vs. resolution.  Regardless of the 
resolution setting, the scale operates internally with the highest resolution; therefore, 
only the displayed value is affected. 

 

 

 

 

 

 

 

 

 

 

 

Units 

Resolution  Kilograms  Pounds 

Pounds 

Ounces 

Ounces 

HIGH 

2 g 

0.005 

lbs 

0.1 oz. 

0.1 oz. 

MEDIUM 

5 g 

.0.010 

lbs. 

0.2 oz. 

0.2 oz. 

LOW 

10 g 

0.020 

lbs. 

0.5 oz. 

0.5 oz. 

TABLE 1.

 Resolution Settings 

 

Summary of Contents for DRS220











Reviews: