Udirc U818A WIFI Manual Download Page 12

19

20

Spare Parts 

For convenience, the spare parts are listed for you to choose, which can be
purchased from the local distributor.

Troubleshooting Guide

The

transmitter

indicator

light is off

Fail to

pair the

drone with

transmitter

The drone

is under-

powered

or can not

fly.

The drone

can not

hover and

tilts to one

side

The drone

indicator

light is off

Can not

see the

picture

Hard to

control by

cellphone

1

2

3

4

5

6

7

Problem

Problem Cause

Solution

No.

1. The transmitter battery is too low.

1. Replace battery.

2. The battery positive pole and negative

    pole are in reverse order.

2. Install the battery in accordance with the

    user manual.

3. Poor Contact.

3. Clean the dirt between the battery and the

    battery alice.

1. Indicator light is off.

1. The same as above 1.2.3.

2. There is interfering signal nearby.

2. Restart the drone and power on the

    transmitter.

3. Misoperation.

3. Operate the drone step by step in

    accordance with the user manual.

4. The electronic component is damaged

    for frequent crash.

4. To buy spare parts from local seller and

    replace damaged parts.

1. The blade deformed seriously.

1. Replace blade.

2. The drone battery is too low. 

2. Recharge the drone battery.

3. Incorrect installation of blade.

3. Install the blade in accordance with the

    user manual instruction.

1. The blade deformed seriously.

1. Replace blade.

2. The motor holder deformed and out of

    verticality.

2. Replace the motor holder.

3. The gyro did not resetting after violent

    crash.

3. Put the drone on the flat ground for

    about 10s or restart the the drone to

    calibrate again.

4. The motor is damaged.

4. Replace motor.

1. The drone battery is too low.

1. Recharge the drone battery.

2. The battery is expired or overdischarge

    protection.

2. Buy a new battery from local seller to

    replace or recharge the battery.

3. Poor contact.

3. Disconnect the battery and then connect

    it with the plug again.

1. Did not connect the wire of camera box

    or poor contact.

1. Check the wire and connect well.

2. There is interfering signal nearby.

2. Cut off the wire and re-connect.

3. Damaged camera.

3. Buy a new camera box from local seller

    to replace.

1. Not experienced enough.

1. Practice and read the cellphone

    controlling instruction carefully.

U818A WIFI-01

Main Frame

U818A WIFI-02

Blade

U818A WIFI-03

Drone Cover

U818A WIFI-04

Base Leg

U818A WIFI-05

Carbon Tube

and Tooth Gear

U818A WIFI-06

Standard Motor 

(Red and Blue Wire)

U818A WIFI-07

Reverse Motor

(Black and

White Wire)

U818A WIFI-08

Standard Motor

Parts (Blue Light)

U818A WIFI-09

Standard Motor

Parts (Red Light)

U818A WIFI-10

Reverse Motor

Parts (Blue Light)

U818A WIFI-11

Reverse Motor

Parts (Red Light)

U818A WIFI-12

Receiving Board

U818A WIFI-13

Camera Box

U818A WIFI-14

TF Card

U818A WIFI-15

Battery

U818A WIFI-16

USB Wire

U818A WIFI-17

Card Reader

U818A WIFI-18

Transmitter

Summary of Contents for U818A WIFI














Reviews: