manualshive.com logo in svg

UDI R/C U64, User Manual, Page: 3 / 14

Share
Download
UDI R/C U64 User Manual Download Page 3

①

Wings installation

Drone tail installation

Slider drone decoration propeller installation

Slider drone doll and hang lift assembly

①

①

Installation: 

Distinguish left and right wings, 

aim at the body hole to push until end.

Disassembly: 

Apply force to pull the wings 
out is fine.

Installation: 

Firstly connect the drone tail to the drone body hole and then rotate the

drone tail, push the upper buckle of drone tail to the drone body buckle.

Disassembly: 

Pull out the drone tail buckle and then rotate to disassemble.

Installation: 

Make sure the slider drone decoration 

propeller to aim at the front buckle and push until end.

Disassembly: 

Apply force to pull out the decoration

propeller.

Installation: 

Hang the doll to the lift and then install the hang lift to the arm slot in

the drone bottom.

Disassembly: 

Pull out one side hook of the hang lift, and then another side to 

remove the doll.

②

③

④

④

Left Wing

Right Wing

Rear

Front

Slider drone parts installation

③

②

3

Summary of Contents for U64















Reviews:

No comments