Doc. 81902B – Rev. 15/03/11
Pag 4 di 7
Dis. 16440/d
WARNING: The following instructions contain
important safety information
•
Prior to installation please read carefully these
instructions (especially the “Safety Notices”).
•
Keep these instructions to consult them after installation
if necessary.
•
Unsuitable application or wrong installation may result in
a loss of system operating functions and consequently in
damages or/and injuries.
•
Only original parts and fittings shall be used to install the
actuator.
•
Designed for applications on top hinged windows and
domes.
•
Possibility of parallel connection to operate more
windows simultaneously.
•
The actuator is for internal use only.
•
The working temperature of actuators are: -10°C +60°C
with maximum relative humidity 60%.
SAFETY NOTICES
•
The actuator shall be installed by qualified personnel.
•
Prior to installation make sure that:
- the actuator performances comply with the estimated
application
- window profiles and fittings are suitable to the stresses
caused by the actuator
- window fittings (hinges) and absence of obstacles allow
complete opening
- the existing electric systems comply with the regulations
in force
- power supply features are those indicated in the actuator
specifications
•
Before connecting the actuator to power supply make
sure it has been turned off to avoid electrocution.
•
An omnipolar switch shall be provided in the supply
mains (according to CEI EN 60335-1).
•
In case the window is accessible at a height of 2,5 m at
least provide the system with an emergency switch off
and/or with additional safety devices.
•
Make sure the supply cable is not subject to stress when
operating.
•
When assembling and disassembling the actuator, take
proper precautions to avoid accidental closing of the
window which might cause injuries to people (impact-
squashing-cutting-shearing).
•
Do not install two actuators on the same window.
•
By feeding the actuator make sure that operation is
regular and that opening and closing end-stroke switches
operate correctly.
•
When operating the actuator follow the following
instructions:
- prevent liquids penetration in the actuator.
- do not approach moving parts until they have come to a
complete stop.
- at least once a year check at sight for damages or wear
in the supply cable.
- to open the window in case of power failure, remove the
split pin (part 4)
- do not carry out any intervention on the actuator, do
not remove or disassemble parts of the actuator: in
case of malfunction or damaged cable contact “UCS”.
INSTALLATION INSTRUCTIONS
The actuator can be mounted using one of the following
kits:
•
(Fig. 1) front-back fitting bracket: bracket “1” is secured
through the holes placed on the actuator top/bottom.
•
(Fig. 2-3) sliding bracket-kit (Part. No 40536W): the
dovetail guide allows bracket “5” to be secured to the
actuator along its entire length.
WARNING:
•
Check allignement between sliding bracket (or front-back
fitting bracket) and connector “2” for the tie–rod “3”
installation.
•
Adjust closing end stroke by means tie-rod “3”.
•
The actuator is supplied with piston rod fully inside and
end-stroke microswitch on: these conditions must be kept
when the window is closed.
•
Follow diagram for electric connection.
GUARANTEE
Ultraflex Control Systems S.r.l. products are guaranteed,
for a period of two years from the manufacture date,
against defects in material and workmanship.
Alleged defective products returned, freight prepaid, within
the above said term, will be repaired or replaced free of
charge, at our option, if found effectively below our quality
standards.
This guarantee does not cover other claims for direct or
indirect damages.
In particular, we decline liability and exclude guarantee
(except for what stated above) if improper installation or
misuse should result in a failure of our products.
CORRECT DISPOSAL OF THIS PRODUCT
The correct disposal of your old appliance will help prevent
potential negative consequences for the environment.
English
Summary of Contents for 40536W
Page 1: ......
