background image

 

EVK-R8 - User guide 

UBX-22018774 - R01 

Document information

 

Page 2 of 20 

C1-Public 

 

 

Document information 

Title 

EVK-R8 

Subtitle 

LENA-R8 series modules evaluation kit 

Document type 

User guide 

 

Document number 

UBX-22018774 

 

Revision and date 

R01 

06-Oct-2022 

Disclosure restriction 

C1-Public 

 

This document applies to the following products: 

Product name 

Type number 

EVK-R8001 

EVK-R8001-00C-00 

EVK-R8001M10 

EVK-R8001M10-00C-00 

 
 
 

 

u-blox or third parties may hold intellectual property rights in the products, names, logos and designs included in this 
document. Copying, reproduction, modification or disclosure to third parties of this document or any part thereof is only 
permitted with the express written permission of u-blox. 

The information contained herein is provided “as is” and u

-blox assumes no liability for its use. No warranty, either express or 

implied, is given, including but not limited to, with respect to the accuracy, correctness, reliability and fitness for a particular 
purpose of the information. This document may be revised by u-blox at any time without notice. For the most recent 
documents, visit www.u-blox.com.  
Copyright © u-blox AG. 

Summary of Contents for ADP-R8001





















Reviews: