background image

ISED Canada

CAN ICES‑3(A)/NMB‑3(A)

This device complies with ISED Canada licence‑exempt RSS standard(s). 
Operation is subject to the following two conditions: 
1.  This device may not cause interference, and 
2.  This device must accept any interference, including interference that 

may cause undesired operation of the device.

This radio transmitter (IC: 6545A‑LBE5ACLR) has been approved by ISED 
Canada to operate with the antenna types listed below with the maximum 
permissible gain and required antenna impedance for each antenna type 
indicated. Antenna types not included in this list, having a gain greater 
than the maximum gain indicated for that type, are strictly prohibited for 
use with this device.
Antenna Information: Antenna, Gain: 26 dBi
The device for operation in the band 5150‑5250 MHz is only for indoor 
use to reduce the potential for harmful interference to co‑channel mobile 
satellite systems.

CAN ICES‑3(A)/NMB‑3(A)

Le présent appareil est conforme aux CNR d’ISDE Canada applicables aux 
appareils radio exempts de licence. L’exploitation est autorisée aux deux 
conditions suivantes :
1.  l’appareil ne doit pas produire de brouillage;
2.  l’appareil doit accepter tout brouillage radioélectrique subi, même si le 

brouillage est susceptible d’en compromettre le fonctionnement.

Le présent émetteur radio (IC : 6545A‑LBE5ACLR) a été approuvé par ISDE 
Canada pour l’exploitation avec l’antenne types énumérés ci‑dessous avec 
le gain maximal admissible et requis l’impédance de l’antenne pour chaque 
type d’antenne indiqué. Types d’antenne non inclus dans cette liste, ayant 
un gain supérieur au gain maximal indiqué pour ce type, sont strictement 
interdits pour une utilisation avec cet appareil.
Informations d’antenne : Antenne, Gain : 26 dBi
Les dispositifs fonctionnant dans la bande 5150‑5250 MHz sont réservés 
uniquement pour une utilisation à l’intérieur afin de réduire les risques 
de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les 
mêmes canaux.

Summary of Contents for LiteBeam 5AC LR

































Reviews: