background image

36

37

Removing the Battery

The 2×2's battery is interchangeable, meaning 
no downtime when working with the bike. Extra 
batteries can be purchased from Ubco Ltd. 
The battery can charge while it is installed in the 
bike or when removed from the bike. Removal is 
not required for charging.

To remove the battery
1. 

Turn off the bike at the key switch and remove 
the key.

2. 

Unplug the battery from the bike. The socket is 
located on the right-hand side of the battery.

3. 

Remove the battery strap.

4. 

Lift the seat. Lift the battery out of the bike with 
two hands 

5. 

Store the battery on a stable, cool, dry surface.

Battery care when charging

•  Keep your battery topped-up. Charge your 

battery overnight at least once a month to 
ensure the health of the battery. 

•  Lithium-Ion batteries do not suffer from the same 

charge memory problems as other batteries, 
therefore can be topped up at any time. 

•  Always charge your bike indoors and at a 

temperature between 0-40°C. Charging the 
battery outside of this temperature range could 
damage your battery or effect performance 
and life span.

•  Store the battery in a cool place indoors. 
•  Due to a low fire risk, always charge the battery 

in a non-flammable environment (on a concrete 
floor, steel shelf, etc).

•  If storing for an extended period, ensure the 

battery has between 50% and 90% charge. 
Storing the battery with either full or too low 
a charge can cause cell damage, reducing 
battery life. 

•  See Section 01 for battery safety.

How to charge the battery (removed 
from bike)

1. 

Turn off the bike at the key switch and remove 
the key.

2.

  Remove the battery from the bike and place it 

on a sturdy, dry, non-flammable surface.

3. 

Plug the provided charger into any standard 
wall socket and switch on at the wall. 

4.

  Plug the charger into the charge port on battery 

and twist to lock.

5. 

The LED indicator lights will signal:

 

GREEN:

 Battery is Full or Disconnected

 

RED - Solid:

 Charging

 

RED - Flashing:

 Charge Error 

 

» Disconnect charger from battery and wall 

socket. Reconnect. If flashing persists 
contact your service provider.

Never store the battery in an 
uncharged state. Doing so can void 
the warranty. Always top up after use. 

Summary of Contents for 2X2






























Reviews: