background image

7

IF YOU WOULD LIKE 

TO

 ORDER 

REPLACEMEN

OR MISSING PA

RT

PLEASE VISI

US A

T:

WWW.THEMDBFAMILY.COM

OR 

YOU CAN CONTACT US BY MAIL

:

MDB FAMILY

855 WASHINGTON BLVD.

MONTEBELLO, CA 90640

We will replace any missing parts at the time 

of  purchase  or  any  defective  item  within 

a  one  year  period  from  the  date  of  original 

purchase.  Please  keep  your  receipt  so  that 

we may process your warranty request. This 

warranty only covers new units with original 

packaging  and  ownership,  and  is  not  trans-

ferable. It does not cover any used, second-

hand or demo models. 

This warranty does not cover any damaged 

or defective parts that result from installation 

and assembly, normal wear and tear, abuse, 

negligence, improper use or alteration to the 

finish,  design,  and  hardware.  The  specific 

legal rights of this warranty may vary from 

state to state. Some states do not allow any 

exclusion or limitation of incidental damages. 

Some  states  do  not  allow  limitation  on  how 

long an implied warranty lasts.  

  

ONE YEAR LIMITED WARRANTY:

Registering your product is even easier than 

before. You can register your product on our 

website at: www.themdbfamily.com

Summary of Contents for u0400

















Reviews: