uAttend DR Series Product Manual Download Page 18

Page: 18 / 24

QUESTIONS? Call 800-518-8925 or email support@trackmytime .com

ADDING THE TEMPERATURE READER

1 . Disconnect your device from the power outlet .
2 . Connect the temperature reader to the top of the time clock .
3 . Plug the cord attached to the temperature reader into the

corresponding port on the time clock .

4 . Reconnect your device to the power outlet to turn on .

REMOVING THE TEMPERATURE READER

1 . Disconnect your device from the power outlet .
2 . Unplug the cord attached to the temperature reader from the

time clock .

3 . Disconnect the temperature reader from the top of the time clock .
4 . Reconnect your device to the power outlet to turn on .

ADD/REMOVE TEMPERATURE READER

Unless you’ve purchased a temperature reader to add to your

DR2000 or you are troubleshooting an issue, there should be

no need to add or remove the temperature reader from your

device . Should you need to add or remove the temperature

reader, follow the simple steps below .

Please note:

Workwell is not advertising its products for use in the medical industry or for medical purposes .

Our products are not intended to diagnose or exclude contagions such as COVID-19, SARS, or any other medical

condition and should not be used as such. Our products are intended to serve as a first-line filter by assisting an

organization and its employees in identifying those employees who may have an elevated body temperature .

While our products may archive readings for reporting and audit purposes, it is solely the responsibility of the

organization to communicate the use of the information to its employees, to obtain any necessary consent

from its employees and to determine how the information is used . The organization should not rely solely on

our products for making such a determination . Various environmental and methodological factors can impact

thermal imaging; therefore, the readings from our products should not be relied upon as the sole determinant

of a person’s body temperature . Competent medical advice and further checks should be sought if there are

concerns regarding an employee’s health or possible illness . Workwell hereby disclaims all liability with respect

to the conditions and limitations described in this paragraph .

Temperature Reader

Cable Port

Summary of Contents for DR Series

























Search results

Summary of Contents for DR Series

Reviews:

Related manuals for DR Series

Brands by name

Popular brands

uAttend DR Series, Product Manual

Search results

Summary of Contents for DR Series

Reviews:

Related manuals for DR Series

Brands by name

Popular brands