INTRODUCTION & SPECIFICATIONS
Surface Prep
Division
P: 877-817- 6687 F: 813-621-7125
Visit us at www.ussaws.com
Model Identification: Record machine serial number plate information
below for future reference
Table of Contents & Introduction .........................................2
Symbols & Decals ............................................................. 3
Safety Instruction .............................................................. 4 - 5
Safety & Operation ....................................................... 6
Parts Breakdown ................................................................... 7
Recommended Cup Wheels ................................................ 8
Warranty & Service .............................................................. 9 - 10
1.0
INSTRUCTIONS FOR USE OF MANUAL SECTIONS
Section Page
2.0 SPECIFICATIONS
Foreword/Introduction
2
The owner’s manual is intended to point out some of the basic safety situa-
tions that may be encountered during the normal operation & maintenance
of the 7” Grinder & to instruct you in safety practices for dealing with these
conditions. Keep all manuals provided with your machine in a safe place at
all times.
The information and specifications included in this publication were
in effect at the time of approval for printing. However, U.S.SAWS reserves
the right to discontinue or change specifications or design at any time with
-
out notice and without incurring any obligation.
The U.S.SAWS 7” Grinder was designed for concrete floor grinding and pol
-
ishing concrete surfaces near walls and other vertical surfaces. This grinder
can be used indoors or outdoors in small or large spaces. The grinder
utilizes 7” diamond cup wheel to level, smooth, or clean the edges of the
concrete slab. The U.S.SAWS 7” grinder features the U.S.SAWS Generation
2 concrete dust shroud system for a clean, dust-free work environment.
TO PREVENT SERIOUS INJURY DO NOT OPERATE SAW WITHOUTPROPER TRAINING AND.
UNDERSTANDING OF THE OWNERS MANUAL
WHEN OPERATING THIS MACHINE
ALWAYS WEAR SAFETY APPROVED
HEARING PROTECTION
EYE OR FACE PROTECTION
PROTECTIVE HELMET
PROTECTIVE GLASSES OR FULL FACE PROTECTION
WEAR HAND PROTECTION
WARNING: Improperly maintaining the JS including the Honda engine or failing to correct a problem before
operation could cause a malfunction resulting in a serious injury. Always perform a pre-operation inspection before
each operation and correct any problem. See Honda Engines Owner's Manual.
5.2
Check the condition of the Honda engine. See the section titled "Before operation - is your
engine ready to go?" in the Honda Engines Owner's Manual.
WARNING: Exhaust gas from gasoline engines contains dangerous carbon monoxide. Breathing it can cause
unconsciousness and even kill you. Always operate gasoline engine machines in a well-ventilated area. Do not
operate in areas where exhaust fumes could accumulate without wearing appropriate respiratory protection.
Consult your employer and OSHA regarding use of appropriate respirator for dangerous carbon monoxide
gases. See Figure 7.
EEnnggiinnee eexxhhaauusstt ccoonnttaaiinnss
ppooiissoonnoouuss ccaarrbboonn
m
moonnooxxiiddee ggaass.. Breathing
it could cause death.
Operate machine in well
ventilated area.
FFiigguurree 77 -- W
Waarrnniinngg llaabbeell -- eennggiinnee eexxhhaauusstt ccoonnttaaiinnss ccaarrbboonn m
moonnooxxiiddee ggaass
1111
DANGER:
Indicates an imminently hazardous situation that, if not avoided,
will result in death or serious injury. This signal word is limited to the most
extreme situations.
WARNING:
Indicates a potentially hazardous situation that, if not avoided,
could result in death or severe injury.
CAUTION:
Indicates a potentially hazardous situation that, if not avoided,
may result in minor or moderate injury. It may also be used to alert against
unsafe practices that may cause property damage.
Dangers, Warnings and Cautions.
The purpose of safety symbols and explanations is to attract your atten-
tion to possible hazards and how to avoid them. The safety symbols and
explanations do not by themselves eliminate any danger. The instructions
or warnings they give are not substitutes for proper accident prevention
measures.
Size
7”
Part Number w/
Convertible Shroud
SX60006CG2
SX60006PPG2
SX60010CG2
Production Capacity
(sq ft/hr)**
150-200
150-200
Grinder Model
Metabo W24-230
Metabo W24-180
Power Source
15 amp Electric
15 amp Electric
RPM
6,600
8,500
Power Requirements
120V, 60Hz
120V, 60Hz
Wheel Diameter
7”
7”
Weight
28 lb
16 lb
