background image

    208-772-0573  

n

  800-257-7982  

n

  FAX: 208-772-0577

VISIT US AT: http://www.usproducts.com

SPECIFICATIONS:

Rotomolded Body:

Vacuum:

VAC Shutoff:

Pump:

Waterlift:

Heat:

Heater:

Wand:

Weight:

Dimensions:

Lifetime Warranty
7.2”, 3-stage
Electronic
Positive displacement, fully adjustable 0-300 psi
140”
Adjustable to 212º F
2000 Watts
Stainless steel, double bend, twin tip
92 lbs.
26.5H x 18W x 28.75L (inches)

TROUBLE SHOOTING:

IF THIS OCCURS

CHECK THIS

NO SPRAY

PUMP DOES NOT RUN

Solution tank is empty.

Clogged spray tip.

Pump not running or not primed.

Valve on wand not operating.

Check the brushes in the pump motor.  Replace if necessary.

No power to pump.  Test the Motor Speed Control Circuit Board and potentiometer.

Debris is plugging cleaning tool or vacuum hose.

Drain gate is not completely closed, or seals are damaged.

Vacuum dome is not seated or is damaged.

No power to motor.

Test the Electronic Float.

Test the switch.

Test the vacuum motor.

Test the Vacuum Circuit Board.

Spraying too long.  Try spraying for 12-15 seconds per cycle.

Heat exchanger needs to be flushed.

Wrong tool being used.  Too much water passing through. Longer hose or larger

diameter hose, than standard

Heat is not turned on.  Either the green light must be on or the bypass switch must

be turned on.

No power in the wall outlet - check to see if the breaker has tripped.

No power to the bypass switch - check wiring for ‘opens.”

No power out of bypass switch, follow troubleshooting steps to isolate the problem.

Call your distributor for additional help.

LOW SUCTION

NO SUCTION

LOW HEAT

NO HEAT

Summary of Contents for HHP-300









Reviews: