Page 4
MODEL UVQ80
U.S. FAN INTERNATIONAL
®
P.O. Box 978
Muskogee, Oklahoma 74402
1
3
8
6
9
10
2
11
7
12
4
5
KEY PART NO.
DESCRIPTION
1
97013576
Grille
2
97014926
Motor Plate
3
99080518
Motor
4
99020276
Impeller
5
99260425
Motor Nut (2 req.)
*
97015159
Blower Assembly (includes Key Nos. 2 thru 5)
6
99270982
Receptacle
7
98009611
Wire Panel
*
97015170
Wire Panel Assembly (includes Key Nos. 6 & 7)
8
97014922
Housing
9
97003932
Damper/Duct Connector
10
98008868
Wiring Plate
11
99150575
Screw, #8-18 x .375
12
99150574
Ground Screw
* Not shown assembled.
Order replacement parts by
“PART NO.” - not by “KEY NO.”
USE AND CARE
SERVICE PARTS
WARRANTY
WARNING: DISCONNECT ELECTRICAL POWER SUPPLY AND
LOCK OUT SERVICE PANEL BEFORE CLEANING OR SERVIC-
ING THIS UNIT.
The motor is permanently lubricated. Do not oil or disassemble
motor.
TO CLEAN GRILLE:
CAUTION: Plastic parts can be cleaned with mild, soapy water (use
a mild detergent, such as dishwashing liquid) and dried with a soft
cloth. Do not use abrasive cloth, steel wool pads, or scouring
powders.
TO CLEAN FAN ASSEMBLY:
Unplug fan assembly. To remove motor plate: Find the single tab on
the motor plate (located next to the receptacle). Push up near motor
plate tab while pushing out on side of housing. Or insert a straight-
blade screwdriver into slot in housing (next to tab) and twist
screwdriver. Gently vacuum fan, motor and interior of housing.
METAL AND ELECTRICAL PARTS SHOULD NEVER BE IM-
MERSED IN WATER.
LIMITED WARRANTY
WARRANTY AND DISCLAIMER: U.S Fan international extends this limited warranty
to the original buyer and warrants that products manufactured by the Company shall
be free from original defects in workmanship and materials for two years from date
of shipment, provided same have been properly stored, installed, serviced, main-
tained and operated. This warranty shall not apply to products which have been
altered or repaired without the Company’s express authorization, or altered or
repaired in any way so as, in the Company’s judgment, to affect its performance or
reliability, nor which have been improperly installed or subjected to misuse, negli-
gence, or accident, or incorrectly used in combination with other substances. The
Buyer assumes all risks and liability for results of use of the products. Warranties
on purchased parts, such as but not limited to bearings, sheaves, belts, couplings,
electric motors, pumps and controls are limited to the terms of warranty extended by
our supplier.Polyethylene tubing and cooling pads are warranted to be free of
defects in material and workmanship for a period of 90 days from date of shipment
and a like warranty applies to the cross fluted cellular type cooling cells for a period
of two years from date of shipment provided same have been properly handled,
stored, installed, serviced, maintained and operated. And further, not subjected to
excessive heat, corrosive agents or chemicals, or mechanical abuse that may
cause tearing, crushing or undue deterioration nor used on a system or in a manner
other than that for which it was designed as explained in the product literature.
LIMITATION OF REMEDY AND DAMAGES: All claims under this warranty must be made
in writing and delivered to P. O. Box 978, Muskogee, Oklahoma, 74402, within 15 days
after discovery of the defect and prior to the expiration of two years from the date of
shipment by the Company of the product claimed defective, and Buyer shall be barred
from any remedy if Buyer fails to make such claim within such period. Within 30 days after
receipt of a timely claim, the Company shall have the option either to inspect the product
while in Buyer’s possession or to request Buyer to return the product to the Company at
Buyer’s expense for inspection by the Company. The Company shall replace, or at its
option repair, free of charge, any product it determines to be defective, and it shall ship the
repaired or replacement product to Buyer F.O.B. point of shipment; provided, however, if
circumstances are such as in the Company’s judgment to prohibit repair or replacement to
remedy the warranted defects, the Buyer’s sole and exclusive remedy shall be a refund to
the Buyer of any part of the invoice price, paid to the Company, for the defective product or
part.The Company is not responsible for the cost of removal of the defective product or
part, damages due to removal, or any expenses incurred in shipping the product or part to
or from the Company’s plant, or the installation of the repaired or replaced product or
part.Implied warranties, when applicable, shall commence upon the same date as the
express warranty provided above, and shall, except for warranties of title, extend only for
the duration of the express warranty. Some states do not allow limitations on how long an
implied warranty lasts, so the above limitation may not apply to you. The only remedy
provided to you under an applicable implied warranty and the express warranty shall be
the remedy provided under the express warranty, subject to the terms and conditions
contained therein. The Company shall not be liable for incidental and consequential losses
and damages under the express warranty, any applicable implied warranty, or claims for
negligence, except to the extent that this limitation is found to be unenforceable under
applicable state law. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you. This
warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.No employee, agent, dealer, or other person is authorized to give any
warranties on behalf of the Company or to assume for the Company any other liability in
connection with any of its products except in writing and signed by an officer of the Com-
pany.
REPLACEMENT PARTS If replacement parts are ordered, buyer warrants that the origi-
nal components in which these replacement parts will be placed are in satisfactory work-
ing condition, and when said replacement parts are installed, the resultant installation will
operate in a safe manner, at speeds and temperatures for which the original equipment
was purchased.
TECHNICAL ADVICE AND RECOMMENDATIONS, DISCLAIMER: Notwithstanding any
past practice or dealings or any custom of the trade, sales shall not include the furnishing
of technical advice or assistance or system design. Any such assistance shall be at the
Company’s sole option and may be subject to additional charge.The Company assumes
no obligation or liability on account of any recommendations, opinions or advice as to the
choice, installation or use of products. Any such recommendations, opinions or advice are
given and shall be accepted at your own risk and shall not constitute any warranty or
guarantee of such products or their performance.
GENERAL In no event shall any claim for consequential damages be made by either
party. The Company will comply with all applicable Federal, State, and local laws.
WARNING
U.S. Fan International products are designed and manufactured to provide reliable perfor-
mance but they are not guaranteed to be 100% free of defects. Even reliable products will
experience occasional failures and this possibility should be recognized by the User. If
these products are used in a life support ventilation system where failure could result in
loss or injury, the User should provide adequate back-up ventilation, supplementary natu-
ral ventilation or failure alarm system, or acknowledge willingness to accept the risk of
such loss or injury. WARNING DO NOT use in HAZARDOUS ENVIRONMENTS where
fan’s electrical system could provide ignition to combustible or flammable materials unless
unit is specifically built for hazardous environments. CAUTION Guards must be installed
when fan is within reach of personnel or within seven (7) feet (2.134 m) of working level or
when deemed advisable for safety. DISCLAIMER The Company has made a diligent effort
to illustrate and describe the products in this literature accurately; however, such illustra-
tions and descriptions are for the sole purpose of identification, and do not express or
imply a warranty that the products are merchantable, or fit for a particular purpose, or that
the products will necessarily conform to the illustrations or descriptions or dimension.
613130
April 2000
99042896B
