background image

QUICK START GUIDE

u-line.com

QUICK START GUIDE

17

u-line.com

During periods of limited use or high ambient 
temperatures, it is common for cubes to fuse together. 
Gently shake the bucket to break apart cubes. If not using 
the ice maker regularly, empty the ice bucket periodically 
to ensure fresh cubes.

It is normal for cubes to appear cloudy. The cause is air 
trapped in the water because of fast freezing. It is not 
caused by the health, taste or chemical make up of the 
water. It is the same air that is in every glass of water you 
drink.

Remove the ice bucket for emptying and cleaning. To 
remove the ice bucket, raise the bin arm and remove the 
bucket from the ice compartment. Use the ice bucket for 
ice storage only.

For parts and service assistance, or to find U-Line factory 
authorized service near you, contact U-Line:        
8900 N. 55

th

 Street, Milwaukee, WI 53223 • u-line.com • 

[email protected] • +1.800.779.2547

Copyright © 2014/2017 U-Line Corporation. All Rights Reserved. 

Publication Number 30630 11/2019 Rev.A

17

QUICK START GUIDE

16

u-line.com

13.Be sure the screws force their way past the opening on 

the gasket channel and sit flush against the bottom of 
the channel.

14.Remove clamps from door/drawer.

If panel requires additional adjustment after 
removing clamps, slightly loosen each screw and 
adjust panel as necessary. Tighten screws upon 
completion.

15.Starting at the corners, re-install the gasket into the 

gasket channel in the frame. Make sure the gasket is 
fully seated. This may take some force.

First Use

All U-Line controls are preset at the factory. Initial startup 
requires no adjustments. 

NOTICE

U-Line recommends discarding the ice produced 
during the first two to three hours of operation 
to avoid possible dirt or scale that may dislodge 
from the water line.

To turn the unit on or off: 

Press the rocker switch located inside the door on the 
front panel, or behind the grille.

Ice

ICE MAKER OPERATION

When the ice bucket is full, the ice making mechanism will 
shut off. However, the refrigeration system will continue 
to cool and maintain the ice supply.

NOTICE

Do not place cans or bottles in the ice 
compartment because they will freeze.

To turn off ice production:

 Raise the bin arm into 

an upright and locked position. The unit will preserve 
temperature for ice storage. 

NOTICE

If not intending to use the ice maker, turn the 
water supply valve off. It is also important to 
raise the bin arm of the ice maker (see above). 
Failure to raise the bin arm may result in damage 
to the water valve.

Certain sounds are normal during the unit’s operation. You 
may hear the compressor or fan motor, the water valve, 
or ice dropping into the ice bucket.

CAUTION

!

NEVER use an ice pick, knife or other sharp 
instrument to separate cubes. Shake the ice 
bucket instead.

Integrated Panel

Integrated Panel

OFF

ON

OFF

ON

Copyright © 2014/2017 U-Line Corporation. All Rights Reserved.

Publication Number 30630 07/2020 Rev. B

Summary of Contents for ULN-SS1095FC-03A






















Reviews: