background image

USER GUIDE

Safety and Warning 1

u-line.com

SAFETY 

• INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

Safety and Warning

NOTICE

Please read all instructions before installing, 
operating, or servicing the appliance.

Use this appliance for its intended purpose only and follow 
these general precautions with those listed throughout this 
guide:

SAFETY ALERT DEFINITIONS

Throughout this guide are safety items labeled with a 
Danger, Warning or Caution based on the risk type:

DANGER

!

Danger means that failure to follow this safety 
statement will result in severe personal injury or 
death.

WARNING

!

Warning means that failure to follow this safety 
statement could result in serious personal injury 
or death.

CAUTION

!

Caution means that failure to follow this safety 
statement may result in minor or moderate 
personal injury, property or equipment damage.

DANGER

!

This unit contains R600a (Isobutane) which is a 
flammable hydrocarbon. It is safe for regular 
use. Do not use sharp objects to expedite 
defrosting. Do not service without consulting the 
“R600a specifications” section included in the 
User Guide. Do not damage the refrigerant 
circuit.

WARNING

!

Service must be done by factory authorized 
service personnel. Any parts shall be replaced 
with like components. Failure to comply could 
increase the risk of possible ignition due to 
incorrect parts or improper service.

4

Summary of Contents for U2224RINT00B





























































Reviews: