U-Line U-CO2175FB-00 Use And Care Manual Download Page 21 | Manualshive

Page: 21 / 25

U-Line U-CO2175FB-00 Use And Care Manual Download Page 21

U-Line Drawer Alignment

18

Minor Adjustment:

Note:

The mounting holes on the

slide are slightly larger than the

screws’ diameter.

1. Loosen one slide’s mounting

screws.

2. Level the slide.

3. Retighten the screws.

4. Repeat procedure for the

other slide.

Severe Adjustment:

Note:

The slides have extra mounting holes that may be used.

1. Loosen one slide’s rear

mounting screws.

2. Remove the slide’s front

mounting screws.

3. Reposition the slide so it is

level.

4. Mark new front drilling holes

using a different set of
mounting holes on the slide.

5. Drill the new holes with a #30 drill bit.

6. Remount the slide.

7. Repeat procedure for the other slide.

Top-to-Bottom (and Left-to-Right) Adjustment

The drawer will need a Top-to-Bottom Adjustment if, when viewed
from the front, the drawer is not level horizontally. Viewed from
the top, one side will protrude. This is caused by one of the slides
being mounted higher than the other slide on the unit’s liner.

Minor Adjustment:

Note:

The mounting holes on the slide are slightly larger than the

screws’ diameter.

1. Loosen one slide’s mounting

screws.

2. Push the slide upward or

downward to match the
position of the other slide.

3. Retighten the screws.

4. Repeat the procedure with

the other slide if necessary.

Severe Adjustment:

Note:

The slides have extra mounting holes that may be used.

1. Remove one slide’s mounting

screws.

2. Reposition the slide so it is

the same distance from the
bottom of the liner as the
other slide. Measure to
confirm.

3. Mark new drilling holes using

different sets of mounting
holes on the slide.

Note:

Front location holes are shown. Corresponding rear holes

will also need to be marked.

4. Drill all the new holes with a #30 drill bit.

5. Remount the slide.

Re-installation of Drawer

CAUTION

Use care when handling the drawer. Drawer edges, drawer
rail and the unit’s slide may be sharp.

1. Set the drawer’s rails onto the slides.

2. Re-install the rails’ mounting screws.

3. Plug in the drawer’s connection wiring (top drawer only).

Not Aligned Left-to-Right

Top View of Unit

Front View of Unit

Not Aligned
Top-to-Bottom

Screws Should

Be Loose

Level the Slide

Mark and Drill New

Mounting Holes

Level the Slide

Push Slide

Upward or

Downward

Mounting Screws

Mark and Drill New

Mounting Holes

Push Slide

Upward or

Downward

«
...
19
20
21
22
23
...
»

Summary of Contents for U-CO2175FB-00


























Reviews:

No comments