U-Line U-BI95 User Manual & Service Manual Download

Page: 46 / 49

USER GUIDE

Troubleshooting - Extended 10

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE •

SERVICE

REPLACING ICE MAKER ASSEMBLY (CO29F
ONLY)

1. Unplug the unit from the main power source.

2. Disconnect ice maker wire harness at plug (1).

3. Remove control capillary tube from sensing tube on ice

maker assembly (2).

4. Remove water inlet tube.

5. Remove front cover (3).

6. Advance the ejector blade to the 3 o’clock position by

turning the 5/16" hex head on the small brass gear
counterclockwise (4).

7. Remove three screws from wall of freezer housing (5).

8. Remove ice maker assembly.

9. Place new ice maker assembly into position and secure

with three screws (5).

10.Reconnect wire harness at plug.

11.Insert control capillary tube into ice maker sensing

tube.

12.Insert water inlet tube.

13.Apply Permagum

to all exit holes.

14.Install back panel.

15.Plug in unit and test.

Figure 7. Ice Maker Assembly

Summary of Contents for U-BI95


















































Search results

Summary of Contents for U-BI95

Reviews:

Related manuals for U-BI95

Brands by name

Popular brands

U-Line U-BI95, User Manual & Service Manual

Search results

Summary of Contents for U-BI95

Reviews:

Related manuals for U-BI95

Brands by name

Popular brands